Standard Accessories; Specified Conditions Of Use - HIKOKI W 18DA Bedienungsanleitung

NOTE
To prevent the battery power consumption caused by
forgetting to turn off the LED light, the light goes off
automatically in about 3 seconds.

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains the
accessories listed on page 192.
Standard accessories are subject to change without notice.

SPECIFIED CONDITIONS OF USE

The tools are suitable for screwing into gypsum plasterboard
on timber and metal substructures
and gypsum fi bre board up to 12.5 mm on metal
substructures.
W18DB is also suitable for gypsum fi bre board up to
12.5 mm on timber substructures and on lay plates,
and for chipboard (OSB) on timber substructures.
The machines are not suitable for inserting and removing
screws in metal materials.
The user bears sole responsibility for any damage caused
by inappropriate use.
Generally accepted accident prevention regulations and the
enclosed safety information must be observed.
SPECIFICATIONS
1. Power tool
Model
Voltage
No load speed 0–5000 min
Screw size
Bit shank size
Battery available
Multi volt battery, BSL18 series
for this tool*
BSL1820M : 1.4 kg
Weight** BSL1840M : 1.6 kg
BSL36B18 : 2.0 kg
* Existing batteries (BSL3660/3620/3626) cannot be used
with this tool.
** According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
2. Battery
Model BSL1820M
Voltage
Battery capacity
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the pilot lamp will blink in red (At 1- second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 4.
W18DA W18DB
18 V
0–3000 min
–1
4 mm
6.35 mm Hex.
BSL1820M : 1.5 kg
BSL1840M : 1.7 kg
BSL36B18 : 2.1 kg
BSL1840M
18 V
2.0 A 4.0 A
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light continuously in
red.
When the battery becomes fully recharged, the pilot lamp
will blink in red. (At 1-second intervals) (See Table 1)
● Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or the
rechargeable battery.
Indications of the pilot lamp (RED)
Lights on for
0.5 seconds and off
Before
for 0.5 seconds
charging
Blinks
Lights continuously
While
Lights
charging
Lights on for
0.5 seconds and off
Charging
for 0.5 seconds
complete
Blinks
Lights on for
1 second and off for
Overheat
0.5 seconds
standby
Blinks
Lights on for
0.1 seconds and off
–1
Charging
for 0.1 seconds
impossible
Flickers
● Regarding the temperatures and charging time of the
battery.
The temperatures and charging time will become as
shown in Table 2.
Battery
Charging voltage
Weight
Temperatures at which the battery
can be recharged
Charging time for battery capacity,
approx. (At 20°C)
1.5 Ah
2.0 Ah
2.5 Ah
3.0 Ah
4.0 Ah
5.0 Ah
6.0 Ah
8.0 Ah
Number of battery cells
NOTE
The recharging time may vary according to temperature
and power source voltage.
9
English
Table 1
Plugged into power
source
—
—
Battery overheated.
Unable to charge.
(Charging will
commence when
battery cools)
Malfunction in
the battery or the
charger
Table 2
Charger
UC18YFSL
V 14.4–18
kg 0.5
0°C–50°C
min 22
min 30
min 35
min 45
min 60
min 75
min 90
min 120
4–10