Product Characteristics - YATO YG-04680 Originalanleitung

GB

PRODUCT CHARACTERISTICS

Pancake maker is a product designed for frying pancakes. Thanks to uniform plate heating, pancakes may be prepared easier and
faster than when using a frying pan. Correct, reliable and safe operation of the product depends on proper operation, therefore:
Before starting product operation, please read this manual and keep it.
The supplier does not assume any liability for any damages resulting from misuse of the product, failure to follow safety regula-
tions and recommendations specifi ed in this manual. Misuse of the product will also result in loss of guarantee and warranty rights
of the user.
EQUIPMENT
The product is delivered complete and does not require assembly. Therefore, before using the product, it is required to remove
all packing and protection elements for transportation. Some preparatory actions described in the further part of this manual are
also required.
GENERAL USE RECOMMENDATIONS
Product is designed for professional use and should be operated by properly qualifi ed personnel.
Product is designed only for heat treating of meals placed directly on a heating plate. It is forbidden to use product for other
purposes, for example as a heater of products kept in a vessel.
Unattended repair, disassembly or modifi cation of product is forbidden. All product repairs must be carried out by an authorised
repair point.
Product should be supervised all the time when operating.
WARNING! During operation the product heats up to high temperature, do not touch the heating plate and product's walls during
operation, it can cause serious burns.
This product is not intended for use by children below 8 years of age and persons with reduced physical or mental capabilities
and person with no experience or knowledge of the equipment. Unless they are supervised or trained how to use the product in a
safe manner so that the risks involved are understood. Children should not play with the product. Unattended children should not
perform cleaning and maintenance of the equipment.
Recommendations for the product transportation and installation
NOTE! Product installation and connecting can be done only by qualifi ed personnel.
Product can be placed only on hard, fl at, level and non-fl ammable surface. Substrate should withstand the weight of appliance
itself together with food placed on it.
Provide at least 10 cm space around product's side walls, do not place any materials not resistant to high temperature above the
product. This will allow proper product ventilation. Do not place the product near edges e.g. of a table.
Do not place any electrical appliances over the product. Water steam is release during operation of product, which may cause a
short circuit of the electrical installation resulting in electric shock.
It is forbidden to drill any hole in the product, nor any other product modifi cation not described herein.
Product to be carried when cooled, by gripping its housing. Do not displace the product by pulling the cable cord.
Temperature at the place of installation and use of product must stay within the range +10 C ÷ +38 C and the relative humidity
O O
must be less than 90%, without steam condensation.
Recommendations for connecting the product to power supply
Before connecting the product to power supply, make sure that the voltage, frequency, and capacity of mains supply correspond
to values shown on the product rating plate. Plug must fi t into the socket. Any modifi cations of plug are forbidden.
Product must be connected directly to a single power outlet. It is forbidden to use extension cords, socket-outlet adapters and
double power outlets. Power supply circuit must be fi tted with a protective conductor and at least 16 A protection circuit.
Avoid any contact of power cord with sharp edges and hot objects and surfaces. When operating the product, the power cord must
always be fully unwound and its position may not interfere with the operation of product. Laying of power cable cannot result in
tripping hazard. Power outlet should be located in such a place to allow always the possibility of quick disconnecting the plug of
power cord supplying the product. When disconnecting the plug of power cord always pull the plug housing, never the cable.
If the power cord or plug is damaged, disconnect it immediately from the mains and contact an authorized manufacturer's service
center for replacement. Do not use the product with a damaged power cord or plug. Power cord or plug cannot be repaired, in
case of damage to these components, replace them with new ones without defects.
Recommendations for using the product
WARNING! Heating plate surface may be hot after the use. Do not touch it as it poses a threat of severe burns. Wait till the heating
plate cools down.
O R I G I N A L I N S T R U C T I O N S
7