Fat (Body Fat); Cleaning And Maintenance; General Cleaning; Belt And Running Deck - Tunturi Cardio Fit T25 Benutzerhandbuch

Fat (Body Fat)

The Body Fat program is program to indicate your fiscal state, based
on your body parameters and heart rate�
To set/ program a program the machine must be in stop mode�
When trainer is in stand by or start up/ operational mode,
press "STOP" button to enter this mode at any time)
- Press "MODE" button to open programming mode, showing P1�
Keep presssing "MODE" until "FAT" is displayed in the speed
window�
- The "Time/ Distance" display shows "1" (SEX) �
The "Time/ Distance" display shows "1"
Press "SPEED +/-" buttons to select:
1: Male/ 2: Female press "MODE" button to confirm�
- The "Time/ Distance" display shows "2" (Age) �
The "Time/ Distance" display shows "25"
Press "SPEED +/-" buttons to select:10~99
press "MODE" button to confirm�
- The "Time/ Distance" display shows "3" (Height) �
The "Time/ Distance" display shows "170"cm
Press "SPEED +/-" buttons to select:100~240 cm
press "MODE" button to confirm�
- The "Time/ Distance" display shows "4" (Weight) �
The "Time/ Distance" display shows "70"kg
Press "SPEED +/-" buttons to select: 20~150 kg
press "MODE" button to confirm�
- The "Time/ Distance" display shows "5" (Active)
The display shows "- - - -" (Measure)
Grab and hold the contact hand-grip heart rate measurement pads
to start the measurement�
‼ NOTE
• During programming, there is no option to go back in the
programming menu� If you made a mistake, you need to start
the full programming process over again�
• Press "MODE" & "SPEED" button simultaneous to return to start
up mode�
⚠ CAUTION
• Holding the contact hand-grip heart rate measurement pads is
required for this function�
Result calculation:
- BODY TYPE: ( Body Fat ratio; 9 types)
• FAT 0 ~19 Underweight
• FAT 20 ~ 25 Standard
• FAT 26 ~ 29 Overweight
• FAT 30 ~ + Obesity
- Press "MODE" button to leave Body Fat program�

Cleaning and maintenance

⚠ WARNING
• Your trainer requires monthly maintenance, even when not being
used�
• Before cleaning and maintenance, remove the mains plug from
the wall socket�
• Do not use solvents to clean the equipment�
- Do not block the ventilation openings� Keep the ventilation
openings clear from dust, dirt and other obstructions�
- Clean the equipment with a soft, absorbent cloth after each use�
- Clean the visible parts of the equipment with a vacuum cleaner
with a small suction nozzle
- Regularly check that all screws and nuts are tight�
⚠ CAUTION
• We recommend to use indoor shoes only on your treadmill�
When you don't have these we do recommend to check the
soles of your footwear before using them on your treadmill�
The treadmill is not sustainable for dirt from outdoors�

General Cleaning

Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt� On a monthly basis: vacuum underneath your treadmill
to prevent build-up�
UNPLUG POWER CORD BEFORE THIS TASK�
Belt Dust
This occurs during normal break-in or until the belt stabilizes� Wiping
off excess dust with a damp cloth will minimize build-up�

Belt and Running Deck

Your treadmill uses a very high-efficient low-friction bed�
Performance is maximized when the running deck is kept clean and
free from dust and dirt� Dirt and dust particles between running deck
and running belt will damage your running deck surface affecting
your performance and product lifetime�
How to clean running deck
Use a soft, dry, non-abrasive cloth to wipe the edge of the belt and
the area between the belt edge and frame� try to reach under the
running belt edges too, to remove the dirt build up on the edges too�
How to clean running belt surface
Firstly use a nylon scrub brush to remove the loose particles from the
running belt surface� Than use wrung out damp cloth (no cleaners or
abrasives) to gentle clean the top of the textured belt� Allow the belt
to fully dry before using�
‼ NOTE
• When your belt too dirty to clean with water only, you can use a
mild soap, but never a lubricant solvent�
• Prevent that the solution comes between running deck and
running belt at all times�
This should be done on a regular basis to extend belt and running
deck life�

Lubrication (fig. F-4)

‼ NOTE
• The Treadmill running belt is pre lubricated before fitting on your
treadmill during the production of the unit� Therefore it is not
needed to lubricate the running belt when taken into use for the
first time�
The running belt must be checked for lubrication condition regularly�
Therefore the treadmill comes with a 300 hours reminder function�
The "TIME WINDOW" will display "OIL" and will make an acoustic
beeping sound every 10 seconds to remind you� Follow the below
checking procedure and eliminate the "OIL" message and acoustic
warning signal by pressing and hold the "STOP" button for at least 3
seconds during this warning signal�
⚠ WARNING
• Before lubrication, remove the mains plug from the wall socket�
1 9
GB