Bosch PCR9A5B90 Montageanleitung Seite 9

Preparing the units
¡ Make a cut-out in the worktop with the required di-
mensions.
¡ In recesses of 500 mm, the appliance must be in-
stalled on the front edge of the recess. → "Posi-
tioning the appliance", Page 9
→ Fig.
2
¡ Seal the cut surfaces of wooden work surfaces
with a special glue seal to protect them from mois-
ture.
¡ If there is no built-in oven underneath the hob, in-
sert a non-flammable separator (e.g. metal or ply-
wood) at a distance of 10 mm from the hob. This
prevents access to the underside of the hob. The
distance from the intermediate floor to the mains
connection for the appliance must be at least 10
mm.
→ Fig. , → Fig.
3 4
Positioning the appliance
Note: Do not use silicone to bond the appliance to
the worktop.
Position the hob with the upper side facing down
1.
on a flat, stable surface.
Apply the adhesive seal supplied to the lower
2.
edge of the hob. The adhesive seal prevents the
penetration of liquids.
→ Fig.
5
Screw the brackets supplied into the specified po-
3.
sition so that they can turn freely.
→ Fig.
6
Turn the hob around and insert it into the recess.
4.
Insert the hob in the front of the recess.
→ Fig.
7
Turn the brackets and tighten them fully.
5.
→ Fig.
8
The position of the brackets depends on the work-
top thickness.
Removing the appliance
Disconnect the appliance from the electricity and
1.
gas connections.
Unscrew the brackets and proceed in reverse or-
2.
der.
Connecting the gas
Observe the country-specific guidelines.
CAUTION ‒ Risk of explosion!
A gas leakage may cause an explosion.
If any connection is handled, check the seal.
▶
¡ Arrange the gas connection so that the shut-off
valve is accessible.
¡ Ensure that the information on the rating plate re-
garding the gas type and gas pressure complies
with the local connection conditions.
¡ Connect the appliance to a fixed gas pipe or a
flexible metal pipe.
¡ The flexible metal pipe must not come into contact
with the moving parts of the unit in which the ap-
pliance is installed (e.g. a drawer) and must not
be routed through any spaces which might be-
come obstructed.
¡ Gas connection on the appliance: G 1/2.
Spare parts for gas connection
You can obtain the gas connection parts from the
technical customer service.
Connecting piece R 1/2"
Gas connection R 1/2
Fit the seal and the connecting piece R 1/2 to the
▶
gas connection on the appliance.
→ Fig.
Gas connection G 1/2
Insert the seal between the gas connection of the
▶
appliance and the gas supply.
→ Fig.
Electrical connection
¡ This appliance is type Y: The connection cable
must only be replaced by technical customer ser-
vice and not by the user. The cable type and the
minimum cross section must be respected.
¡ The hobs are supplied with a power cord with or
without a plug.
¡ Only connect appliances that are fitted with a plug
to a correctly installed socket with protective earth
conductor.
¡ If the plug is not accessible to the user, an all-pole
isolating safety switch with a minimum contact
opening of 3 mm must be provided.
→ Fig.
Converting the gas type
If the country's regulations allow, this appliance can
be adapted to other types of gas, if these are listed
on the rating plate.
You can find the right parts in the bag that is sup-
plied with the appliance or you can obtain them from
customer service. The table → Fig.
right combination for the relevant burner and gas
type.
Economy burner
Standard-output burner
High-output burner
Dual-wok multi-crown burner
¡ 1 - Outer flame
¡ 2 - Inner flame
Adjusting the taps
Turn the rotary knobs to the minimum power posi-
1.
tion and pull them out.
With the tip of the screwdriver, push down on the
2.
flexible rubber holder to access the bypass screw.
→ Fig.
Never remove the sealing ring. The sealing rings
prevent liquids and dirt from finding their way into
the appliance and impairing its ability to function
properly.
When adjusting the bypass screws (M), refer to
3.
the table → Fig.
A: Firmly tighten the bypass screws.
‒
B: The bypass screws must be flush with the fit-
‒
ting.
→ Fig.
Replacing the nozzles
Remove all pan supports, burner caps and distrib-
1.
utors.
Replace the nozzles using the appropriate wrench
2.
and tighten them carefully to guarantee the seal.
→ Fig.
Ensure that the nozzle does not become detached
during removal or fastening.
00427950
Reinstalling the appliance
Install the appliance components in reverse order.
▶
9
10
11
12
.
16
13
, → Fig.
14 15
shows the
16
9