Safety Instructions - nania D12 Bedienungsanleitung

Thank you for purchasing this Group 0-1-2 car seat. If you require assistance with this product or if you wish to
change an accessory, please contact our customer service department (see details on reverse).

SAFETY INSTRUCTIONS

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION. IF THE SEAT IS NOT
INSTALLED CORRECTLY, YOUR CHILD'S SAFETY MAY BE AT RISK. DO NOT USE THIS CHILD SEAT ON A PASSEN-
GER SEAT FITTED WITH AN AIR BAG!
The seat may be installed in a front-facing or rear-facing position with a 3-point safety belt to UN/ECE No.16
standard or equivalent. Do not use it on side-facing or rear-facing seats. Always remember to fasten and cor-
rectly adjust the child's harness and never start the car without first checking that the seat is properly fixed to the
passenger seat as shown in these instructions. It is important to check that the straps of the seat belt are fully
tightened and that the harness lap strap is positioned as low as possible to support your child's pelvis. Check that
the seat belt and harness straps are not twisted. For maximum protection, there must be no slack between the
car seat and the passenger seat. Please refer to the method recommended in these instructions. The seat must
not be modified in any way and no elements should be added. It is recommended that you replace this car seat if
it has been subjected to a severe impact following an accident or in case of wear. You should regularly check that
the harness is not showing signs of wear; check in particular the harness points, the seams and the adjustment
devices. Never leave your child unattended in the seat. Check that no part of the seat is trapped in the door or in
a fold-down passenger seat. If your car has a fold-down rear seat, check that it is correctly locked in the vertical
position. Direct exposure to the sun increases the temperature inside vehicles. For this reason, you are advised to
cover the child's car seat when not in use in order to prevent the elements, in particular the fixations, from getting
hot and burning the child. Do not use your car seat without its cover and only replace it with a cover that has been
recommended by the manufacturer. In an emergency, the child must be able to be freed quickly. The buckle, which
can be easily opened, must therefore not be covered. Teach your child not to play with the buckle. Always remem-
ber to check that there are no scraps of food or other remains in either the harness buckle or the central adjuster.
Luggage and other heavy or sharp objects must be fixed down in the car. Objects that are not attached may injure
a child in the event of an accident. In winter, make sure that the child is not wearing over-bulky clothes.
The correct type of safety belt to use with your car seat
Your car seat must ONLY be installed on a passenger seat fitted with a 3-point safety belt (1). NEVER install your
car seat on a passenger seat fitted with a 2-point safety belt (2)!
Your Gr. 0-1-2 car seat
This is a Group 0-1-2 car seat that is designed for children weighing between 0 and 25 kg.
A. Cover
B. Pillow (some models only)
C. Shoulder pad (x2)
D. Infant reducer cushion (some models only)
E. Adjuster (x2)
F. Adjustment strap (x2)
G. Shell
H. Harness buckle
I. Belt guides for rear-facing use
J. Belt guides front-facing use
Adjusting the harnesses
Make sure that the harness of your car seat is adapted to the height of your child before starting to install
the seat in your car. The harnesses can be adjusted to 4 different heights and must be positioned as close as
possible to your child's shoulders (4).
• The two lower positions are ONLY intended for use in group 0, for a child weighing from 0 to 10 kg in a rear-
facing position. If your child's shoulders are between two levels in a rear-facing configuration, choose the lower
of the two.
• The two upper positions are ONLY intended for use in group 1, for a child weighing from 9 to 18 kg in a front-
facing position. If your child's shoulders are between two levels in front-facing configuration, choose the higher
of the two.
To adjust the height of the harnesses, remove the upper section of one of the harness straps by pivoting the metal
anchor located behind the back rest and then pulling it through the slots of the shell and cover (5). Repeat the
operation on the upper section of the second strap.
All manuals and user guides at all-guides.com
(3)
GB
13
User Guide - GB