AEG of 500 s Gebrauchsanleitung Seite 2

Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Mains
connection
ENGLISH
You are demanding and expect to purchase quality goods – quality offered by Atlas
Copco. We have built a durable and reliable electric power tool for you.
Please read the instructions for use before first operation so you can handle your
power tool effectively and safely. We are sure that buying an AEG Electric Power
Tool from Atlas Copco was the right choice!
Nominal power . . . . . . . . . . . . . . . . . . . . . . . .
No-load speed . . . . . . . . . . . . . . . . . . . . . .
Maximum no–load speed in case of
ineffective no–load speed limitation
Cage stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Collet diameter . . . . . . . . . . .
Router diameter (HSS/HM)
Abrasive grinding body diam. max.
for ceramic resin
for plastic resin
Gear neck diameter
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
*Not included in standard equipment, available as an accessory.
J Please pay attention to the safety instructions in the attached leaflet!
J Always use the protective shields on the machine.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Always disconnect the plug from the socket before carrying out any work on the
machine.
Only plug-in when machine is switched off.
J Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
J Only use professionally grinded router cutters.
J All inserted tools which are used must be admitted for the max. speed of rotation!
J The workpieces sould be clamped down before cutting.
J Put the router back to original position after usage (loosen clamping lever to secure
cage).
J After switching off, the machine will not be idle immediately. (After–running of the
work spindle.)
J Only move the workpiece in counter rotation to cutter (only work oppositely oriented)!
For security, use devices such as safety– and pressure device, guide slide, rip fence,
etc.
J For ceramic abrasives or silicane rubber polishers with a safe peripheral speed of
45 m/s, the grinding body diameter must not exceed 20 mm.
With synthetic resin plastic abrasives with a safe peripheral speed of 80 m/s, the
grinding body diameter must not exceed 38 mm
J The dust that arises when working with this tool can be detrimental to health (e.g.
when working oak or beech wood, stones, paint, which could contain lead or other
harmful chemicals) and therefore not reach the body.
Use a dust absorption system and wear a suitable dust protection mask.
Remove deposited dust thoroughly, e.g. with a vacuum cleaner.
J Typically the A-weighted noise levels of the tool are:
Sound pressure level = 82 dB (A). Sound power level = 95 dB (A).
Wear ear protectors!
J Typically the weighted acceleration is 4 m/s
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
1
. . . . . . . . .
6 mm, 8 mm, 1/4"*
. . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
OF 500 S
500 W . . . . . . . . . . . . .
-1
34 000 min . . . . . . . .
– . . . . . . . . . . . . . .
50 mm . . . . . . . . . . . . .
. . 6 mm, 8 mm, 1/4"*
max. 36 mm . . . . . . . .
20 mm . . . . . . . . . . . . .
38 mm . . . . . . . . . . . . .
43 mm . . . . . . . . . . . . .
2,9 kg . . . . . . . . . . . . .
2
.
OFE 710
710 W
-1
30 000 min
-1
39 000 min
50 mm
max. 36 mm
20 mm
38 mm
43 mm
2,9 kg
OF 500 S, OFE 710