Electrical Installation; Wiring Diagrams; Operating Environment - Sygonix 2377679 Bedienungsanleitung

Operating Instructions
PIR Ceiling Motion Sensor, 360°
Item no: 2377679
1 Intended use
The product is a ceiling mounted infrared (PIR) motion sensor that connects to the mains power supply.
You can set a switch-on time to control how long the connected load stays on and adjust the switching
threshold based on ambient light levels.
The product is designed for private use only.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to
third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.
2 Delivery contents
■
Product
■
2x Screws for bracket
■
2x Wall plugs
■
Operating instructions
3 Latest product information
Download the latest product information at
low the instructions on the website.
4 Description of symbols
The symbol with the exclamation mark in the triangle is used to indicate important informa-
tion in this document. Always read this information carefully.
Risk of electric shock!
Protection class 2 (double or reinforced insulation, protective insulation).
This product must only be used in dry, enclosed indoor areas. It must not become damp or
wet, as this may cause a fatal electric shock!
The arrow symbol indicates special information and advice on operation.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety informa-
tion. If you do not follow the safety instructions and information on proper handling,
we assume no liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
5.1 General
■
The product is not a toy. Keep it out of the reach of children and pets.
■
Do not leave packaging material lying around carelessly. This may become dangerous playing mater-
ial for children.
■
If you have questions which remain unanswered by this information product, contact our technical
support service or other technical personnel.
5.2 Handling
■
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
■
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
■
Consult an expert when in doubt about the operation, safety or connection of the appliance.

5.3 Operating environment

■
Do not place the product under any mechanical stress.
■
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
■
Protect the product from high humidity and moisture.
■
Protect the product from direct sunlight.
3
www.conrad.com/downloads or scan the QR code shown. Fol-

5.4 Electrical installation

WARNING! Safety hazard!
The product should only be installed by people with relevant electrical knowledge and experience! *)
If it is not installed properly, you risk:
■
your own life
■
the life of user of the electrical device
■
severe damage to property, e.g., by fire
■
personal liability for personal injury and material damage
Always consult an electrician!
*) Technical knowledge required to perform the installation:
For the installation, the following specialist knowledge is required in particular:
■
The "Five safety rules": Disconnect from the mains; protect against accidental switch-on; ensure there
is no voltage; earth and short-circuit; cover or protect adjacent live parts
■
Use of suitable tools, measuring devices and personal protective equipment, where necessary
■
Analysis of measurement results
■
Use of electrical installation materials to meet the requirements for disconnection
■
IP protection ratings
■
Installation of electrical installation materials
■
Type of power supply (TN system, IT system, TT system) and the corresponding connection criteria
(classic earthing, protective earthing, necessary additional measures etc.)
If you are not a professional, do not do it yourself, have it performed by a specialist.
6 Installation
Important:
– Risk of fatal electric shock! Electrical installation to be carried out by a licensed profes-
sional.
– Observe the "Safety instructions", especially the "Electrical installation" warning.
Installation consists of two parts, electrical connection and mounting.

6.1 Wiring diagrams

L
6.2 Mounting
N L
N N L
N L