Inhaltszusammenfassung für led2work SPOTLED II Aufbau
Seite 1
MASCHINENBELEUCHTUNG MACHINE LIGHTING ÉCLAIRAGE DE MACHINES ILUMINACIÓN DE MÁQUINAS ILLUMINAZIONE MACCHINA SPOTLED II Aufbau Betriebsanleitung | LED-Aufbauleuchte Operating Instructions | LED surface-mounted luminaire Manuel d’utilisation | Luminaire LED en saillie Manual de instrucciones | Luminaria LED de superficie Istruzioni per l’uso | Lampada a LED per montaggio a superficie / 2014 / 35 / EU BA 03/2022...
Seite 2
| Zeichnungen | Drawings | Schémas | Dibujos | Disegni SPOTLED II Aufbau SPOTLED II V4A Aufbau, OEM OPTION 2 | BA SPOTLED II Aufbau . BA 03/2022...
Gerät ist die Last nicht galvanisch vom Netz getrennt. Verwenden Sie das Gerät nur in technisch einwandfreiem Zustand, sicherheits- und gefahrenbewusst. Sind Warnhinweise bzw. -symbole auf der Leuchte angebracht, dürfen diese nicht entfernt werden. 4 | BA SPOTLED II Aufbau . BA 03/2022...
Bei Befestigung der Leuchte ist darauf zu achten, dass die Leuchte sicher und stabil befestigt wird. Beim Herunterfallen der Leuchte besteht auf Grund des Eigengewichts Verletzungsgefahr! 5 | Anschluss Geeignetes Anschlussmaterial, Leitungen und Zubehör finden Sie im Zubehörangebot von LED2WORK. Die PIN-Belegung des M12 Steckers ist wie folgt: Schemazeichnung M12-Stecker Mögliche Varianten M12-Stecker...
+49 7231 44920-00 Montag bis Donnerstag: 8:00 Uhr bis 12:00 Uhr und 13:00 Uhr bis 16:30 Uhr Freitag: 8:00 Uhr bis 12:00 Uhr und 13:00 Uhr bis 15:00 Uhr Per e-mail: info@led2work.com 6 | BA SPOTLED II Aufbau . BA 03/2022...
BA SPOTLED II Aufbau 10 | Technische Daten Anschlusswerte 24V DC ±10 % Schutzklasse Abstrahlwinkel (Optik) 16°/25°/40° Lebensdauer LED > 50.000 h (L80/B10) Betriebstemperatur -10… +40°C | SPOTLED II V4A: -30... +40°C Schutzart IP67 Techn. Sicherheitsprüfung DIN EN 62471 Lichtfarbe...
Seite 8
Gives you additional information for the safe and efficient use of the product. Refers to compliance with these operating instructions. CE marking: confirms conformity with applicable standards and regulations. 8 | BA SPOTLED II Aufbau . BA 03/2022...
(SELV – protection class III), smallest discharge currents may occur when contact is made. According to DIN VDE 0701 – 0702, this discharge current must be limited to a maximum of 0.5 mA. All corresponding products from LED2WORK GmbH fall significantly below this specification.
If the luminaire falls down, its weight poses a risk of injury! 5 | Connection Suitable connection material, cables and accessories can be found in the accessory range of LED2WORK. PIN assignment of the M12 connector is as follows:...
BA SPOTLED II Aufbau 6 | Maintenance and Care The LED luminaire is maintenance-free. Do not make any alterations to the luminaire (except according to the mounting information contained in this manual). Do not open the luminaire! The LED light sources mounted in the luminaire are connected to the luminaire housing in a special way (thermal coupling) and may react sensitively to electrostatic discharges (ESD).
SPOTLED II V4A Aufbau, OEM 111111-21 16° 0,35 A ~8,5 W SPOTLED II V4A Aufbau, OEM 111112-21 25° 0,35 A ~8,5 W SPOTLED II V4A Aufbau, OEM 111113-21 40° 0,35 A ~8,5 W 12 | BA SPOTLED II Aufbau . BA 03/2022...
Seite 13
BA SPOTLED II Aufbau FRANÇAIS Sommaire 1 | Utilisation conforme 2 | Pour un fonctionnement sûr 3 | Consignes de sécurité 4 | Montage/fixation 5 | Raccordement 6 | Maintenance et entretien 7 | Garantie 8 | Mise au rebut 9 | Service clientèle...
(classe de protection III), il peut y avoir de faibles courants de fuite en cas de contact. Se- lon la norme DIN VDE 0701 – 0702, ce courant doit être limité à 0,5 mA maximum. Cette norme est clairement respectée par tous les produits de la société LED2WORK concernés. 3 | Consignes de sécurité...
BA SPOTLED II Aufbau À partir de températures ambiantes > 40°C, le luminaire doit être directement relié à une surface métallique d'environ 150 x 150 mm. L’utilisation d’une pâte thermique est recommandée. Lors de la fixation du luminaire, veiller à ce que le luminaire soit fixé de manière sûre et stable.
Le luminaire doit être apporté à un point de collecte approprié, aux fins de recyclage des équipements électriques et électroniques, conformément à la réglementation en vigueur dans le pays concerné. (N° WEEE 32828318) 16 | BA SPOTLED II Aufbau . BA 03/2022...
BA SPOTLED II Aufbau 9 | Service clientèle N’hésitez pas à nous contacter en cas de problèmes ou de questions sur ce produit ! Par téléphone : +49 7231 44920-00 Du lundi au jeudi de 8h00 à 12h00 et de 13h00 à 16h30 Le vendredi de 8h00 à...
Es obligatorio leer las consignas de seguridad y el resto de información de este manual de instrucciones. Lee detenidamente todo el manual de instrucciones antes del montaje y la puesta en marcha. 18 | BA SPOTLED II Aufbau . BA 03/2022...
ón SELV (clase de protección III), se pueden producir bajas corrientes de fuga al entrar en contacto. Esta corriente se debe limitar a 0,5 mA como máximo conforme a la norma DIN VDE 0701-0702. Todos los productos correspondientes de LED2WORK GmbH quedan muy por debajo de esta especificación.
5 | Conexión En la tienda de accesorios de LED2WORK encontrarás material adecuado para la conexión, cables y accesorios. La asignación de pines del conector M12 es la siguiente:...
BA SPOTLED II Aufbau 6 | Mantenimiento y cuidado La luminaria LED no requiere mantenimiento. No realices modificaciones, excepto las que se indican en este manual de instrucciones para el montaje. No se debe abrir la luminaria. Las fuentes de luz LED montadas en la luminaria están conectadas de manera especial con la carcasa (acoplamiento térmico) y son muy sensibles a las descargas electrostáticas (ESD).
SPOTLED II V4A Aufbau, OEM 111111-21 16° 0,35 A ~8,5 W SPOTLED II V4A Aufbau, OEM 111112-21 25° 0,35 A ~8,5 W SPOTLED II V4A Aufbau, OEM 111113-21 40° 0,35 A ~8,5 W 22 | BA SPOTLED II Aufbau . BA 03/2022...
BA SPOTLED II Aufbau ITALIANO Indice 1 | Uso conforme 2 | Per un funzionamento sicuro 3 | Avvertenze di sicurezza 4 | Montaggio/Fissaggio 5 | Collegamento 6 | Manutenzione e cura 7 | Garanzia 8 | Smaltimento 9 | Assistenza clienti 10 | Dati tecnici Dati conformi al Regolamento UE sull’ecodesign 2019/2020/UE...
SELV (classe di isolamento III), in caso di contatto potrebbero verificarsi esigue correnti di dispersione. Tale corrente va limitata, secondo la norma DIN VDE 0701 – 0702, a 0,5 mA max. Tutti i prodotti interessati della ditta LED2WORK GmbH presentano valori inferiori.
È necessario fissare la lampada in modo saldo, sicuro e stabile. Dato il peso, in caso di caduta della lampada sussiste il rischio di lesioni. 5 | Collegamento Il materiale di collegamento idoneo, cavi e accessori rientrano nella gamma di accessori LED2WORK. L’assegnazione PIN del connettore M12 è la seguente: Disegno schematico connettore M12...
+49 7231 44920-00 (Inglese preferito) Da lunedì a giovedì dalle ore 8.00 alle 12.00 e dalle 13.00 alle 16.30 Il venerdì dalle ore 8.00 alle 12.00 e dalle 13.00 alle 15.00 Via mail: info@led2work.com 26 | BA SPOTLED II Aufbau . BA 03/2022...
BA SPOTLED II Aufbau 10 | Dati tecnici Dati collegamento 24V DC ±10 % Classe di isolamento Apertura del fascio di luce 16°/25°/40° Durata dei LED > 50.000 h (L80/B10) Temperatura di esercizio -10… +40°C | SPOTLED II V4A: -30... +40°C...
La denominazione 2941-1660-00-LE-d40 corrisponde a una sorgente luminosa con classe di efficienza energetica F Light Engine Art.-Nr. Product no. 2941-1660-00-LE-d40 N° d’article Nº de artículo Articolo no. 111111-11 111112-11 111113-11 111111-21 111112-21 111113-21 28 | BA SPOTLED II Aufbau . BA 03/2022...
Seite 29
BA SPOTLED II Aufbau www.led2work.com | shop.led2work.com | 29...
Seite 30
LED2WORK GmbH Stuttgarter Str. 13 A 75179 Pforzheim | Germany T +49 7231 44920 -00 info@led2work.com www.led2work.com...