Ec Declaration Of Conformity; Transporting Lithium Batteries - Milwaukee M12 HPT Originalbetriebsanleitung

Pressgerät

Vorschau ausblenden Andere Handbücher für M12 HPT:

Originalbetriebsanleitung (101 Seiten)

100

101

102

103

104

105

Inhalt

106

Seite von 106

/ 106
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

After nishing the work, check the installation with appropriate

testing equipment and assure that it is leakproof!

The press device is not suitable for continuous operation. Following

30 minutes of continuous operation, a short break of at least 15

minutes must be taken to allow the device to cool down.

SPECIFIED CONDITIONS OF USE

The devices and the press jaws are designed exclusively for the

press- tting of pipes and ttings for which the relevant press jaws

are intended.

These press devices are intended exclusively for use with press jaws

approved by Milwaukee in agreement with the system supplier.

BATTERIES

Battery packs which have not been used for some time should be

recharged before use.

Temperatures in excess of 50°C (122°F) reduce the performance of

the battery pack. Avoid extended exposure to heat or sunshine (risk

of overheating).

The contacts of chargers and battery packs must be kept clean.

For an optimum life-time, the battery packs have to be fully

charged, after use.

To obtain the longest possible battery life remove the battery pack

from the charger once it is fully charged.

For battery pack storage longer than 30 days: Store the battery

pack where the temperature is below 27°C and away from moisture

Store the battery packs in a 30% - 50% charged condition Every six

months of storage, charge the pack as normal.

Do not dispose of used battery packs in the household refuse or

by burning them. Milwaukee Distributors o er to retrieve old

batteries to protect our environment.

Do not store the battery pack together with metal objects (short

circuit risk).

Use only System C12 chargers for charging System C12 battery

packs. Do not use battery packs from other systems.

Never break open battery packs and chargers and store only in dry

rooms. Keep dry at all times.

Battery acid may leak from damaged batteries under extreme load

or extreme temperatures. In case of contact with battery acid wash

it o immediately with soap and water. In case of eye contact rinse

thoroughly for at least 10 minutes and immediately seek medical

attention.

No metal parts must be allowed to enter the battery section of the

charger (short circuit risk).

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legisla-

tion requirements.

Transportation of those batteries has to be done in accordance with

local, national and international provisions and regulations.

The user can transport the batteries by road without further

requirements.

Commercial transport of Lithium-Ion batteries by third parties is

subject to Dangerous Goods regulations. Transport preparation and

transport are exclusively to be carried out by appropriately trained

persons and the process has to be accompanied by corresponding

experts.

When transporting batteries:

Ensure that battery contact terminals are protected and insulated

to prevent short circuit. Ensure that battery pack is secured against

movement within packaging. Do not transport batteries that are

cracked or leak. Check with forwarding company for further advice

MAINTENANCE

Check that the press jaw and drive rolls move freely.

Clean and grease the press drives, locking bolts and press jaws

when you have nished work.

Service and repair work may only be carried out by authorised

specialist workshops.

The device contains hydraulic uid. Hydraulic uids pose a hazard

to groundwater. Uncontrolled draining or improper disposal is

punishable by law.

The next service deadline is indicated on the press device. This

service must be performed at least every 2 years or at the latest

when the LED display indicates that a service is due.

Replace worn press tools.

The ventilation slots of the machine must be kept clear at all times.

Use only Milwaukee accessories and Milwaukee spare parts. Should

components need to be replaced which have not been described,

please contact one of our Milwaukee service agents (see our list of

guarantee/service addresses).

If needed, an exploded view of the tool can be ordered. Please state

the Article No. as well as the machine type printed on the label

and order the drawing at your local service agents or directly at:

Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnen-

den, Germany.