Technical Data; Noise Information; Working Instructions - Milwaukee M12 HPT Originalbetriebsanleitung

TECHNICAL DATA

Press device
Production code
Battery voltage
Power consumption
Nominal force
Compression range max. :
Ø Plastics
Ø Metal
Weight according EPTA-Procedure 01/2003
(M12 HPT / Li-Ion 2.0 Ah / J12-Th14)
(M18 HPT / Li-Ion 2.0 Ah / J18-Th14)
Weight (M12 HPT / Li-Ion 2.0 Ah)
(M18 HPT / Li-Ion 2.0 Ah)

Noise information

GB
Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Vibration emission valuea
Uncertainty K=
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent applications, with
di erent accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running
but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury. Save all warnings and
instructions for future reference.
PRESS DEVICE SAFETY WARNINGS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is recom-
mended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
Never hold your ngers or other body parts in the working area of
the cylinder or the press jaws.
Do not hold the jaw levers with your hands during the pressing
operation.
The crimping tool and dies must only be used by trained personnel.
Check the press tools and press devices for cracks and other signs of
wear before each use.
Only use press tools and press devices that are in perfect technical
condition.
Have damage repared immediately by an authorised workshop.
English Deutsch
18
h
M12 HPT
4430 86 03...
... 000001-999999
12 V
240 W
19 kN
40 mm
35 mm
2,8 kg
1,7 kg
75,5 dB (A)
86,5 dB (A)
<2,5 m/s
1,5 m/s
The machine may only be used with a press jaw inserted into it.
In the event of problems during the pressing process, press the
Emergency Stop button immediately and release the ON switch.
The valve will open and the piston will return to its initial position.
Compliance with the speci ed service work and service intervals is
mandatory.
Remove the battery pack before starting any work on the
appliance.

WORKING INSTRUCTIONS

Use only system-compatible press ttings and press jaws designed
for them.
Consult the documents provided by the system supplier for hand-
ling and assembly instructions for ttings and pipes.
Check whether the nominal width of the press tting corresponds
to the nominal width of the press jaws.
Make sure that the press jaw is fully closed when pressing is
complete.
Imperfect pipe joints must be compressed again using a new
tting.
M18 HPT
4431 16 03...
... 000001-999999
18 V
450 W
32 kN
110 mm
54 mm (108 mm)
dep. on system
5,2 kg
3,3 kg
76,5 dB (A)
87,5 dB (A)
<2,5 m/s
2 2
1,5 m/s
2 2