Mode Select; Temperature Setting - Mitsubishi Electric Mr.SLIAM SLZ-KA25VAQ2 Bedienungshandbuch

5. Operation
<To Stop Operation>
■ Press the ON/OFF button 1 again.
• The ON lamp 1 and the display area go dark.
Note:
Even if you press the ON/OFF button immediately after shutting down the opera-
tion is progress, the air conditioner will not start for about three minutes. This
is to prevent the internal components from being damaged.
5.2. Mode select
■ Press the operation mode (
tion mode 2 .
Cooling mode
Drying mode
Fan mode
Heating mode
Automatic (cooling/heating) mode
Ventilation mode
Only indicated on the following condition
Wired remote controller used
LOSSNAY connected
Information for multi system air conditioner (Outdoor
unit: MXZ series)
► M ulti system air conditioner (Outdoor unit: MXZ series) can connect
two or more indoor units with one outdoor unit. According to the
capacity, two or more units can operate simultaneously.
• When you try to operate two or more indoor units with one outdoor unit
simultaneously, one for the cooling and the other for heating, the opera-
tion mode of the indoor unit that operates earlier is selected. The other
indoor units that will start the operation later cannot operate, indicating
an operation state in flashing.
In this case, please set all the indoor units to the same operation
mode.
• There might be a case that the indoor unit, which is operating in
(AUTO) mode. Cannot change over to the operating mode (COOL ↔
HEAT) and becomes a state of standby.
• When indoor unit starts the operation while the defrosting of outdoor unit
is being done, it takes a few minutes (max. about 15 minutes) to blow
out the warm air.
• In the heating operation, though indoor unit that does not operate may
get warm or the sound of refrigerant flowing may be heard, they are not
malfunction. The reason is that the refrigerant continuously flows into it.
Automatic operation
■ According to a set temperature, cooling operation starts if the room tem-
perature is too hot and heating operation starts if the room temperature
is too cold.
■ During automatic operation, if the room temperature changes and remains
2 °C or more above the set temperature for 15 minutes, the air conditioner
switches to cooling mode. In the same way, if the room temperature
remains 2 °C or more below the set temperature for 15 minutes, the air
conditioner switches to heating mode.
Cooling mode
15 minutes (switches from
cooling to heating)
■ Because the room temperature is automatically adjusted in order to
maintain a fixed effective temperature, cooling operation is performed a
few degrees warmer and heating operation is performed a few degrees
cooler than the set room temperature once the temperature is reached
(automatic energy-saving operation).
6
) button 2 and select the opera-
15 minutes (switches
from heating to cooling)
Set temperature +2°C
Set temperature
Set temperature -2°C
5.3. Temperature setting
► T o decrease the room temperature:
Press button 3 to set the desired temperature.
The selected temperature is displayed 3 .
► T o increase the room temperature:
Press button 3 to set the desired temperature.
The selected temperature is displayed 3 .
• Available temperature ranges are as follows:
Cooling/Drying: 19 - 30 °C
Heating: 17 - 28 °C
Automatic: 19 - 28 °C
• The display flashes either 8 °C or 39 °C to inform you if the room tem-
perature is lower or higher than the displayed temperature.
5.4. Fan speed setting
■ Press the Fan Speed button 5 as many times as necessary while the
system is running.
• Each press changes the force. The currently selected speed is shown
at 5 .
• The change sequence, and the available settings, are as follows.
Remote controller display
Fan speed
Low
▼
( )
3-stage
• Display for the wireless remote controller are shown in parentheses.
Note:
●
The number of available fan speeds depends on the type of unit connected.
Note also that some units do not provide an "Auto" setting.
●
In the following cases, the actual fan speed generated by the unit will differ
from the speed shown the remote controller display.
1. While the display is showing "STAND BY" or "DEFROST".
2. When the temperature of the heat exchanger is low in the heating mode.
(e.g. immediately after heating operation starts)
3. In HEAT mode, when room temperature is higher than the temperature
setting.
4. When the unit is in DRY mode.
5.5. Airflow direction setting
<To Change the Airflow's Up/Down Direction>
■ With the unit running, press the Airflow Up/Down button 6 as neces-
sary.
• Each press changes the direction. The current direction is shown at 6 .
• The change sequence, and the available settings, are as follows.
For wireless remote controller
→ 2 → 3
1
For wired remote controller
1 Horizontal airfrow 30°
2 Downword airfrow 45°
3 Downword airfrow 55°
* Note that during swing operation, the directional indication on the screen
does not change in sync with the directional vanes on the unit.
* Some models do not support directional settings.
Note:
●
Available directions depend on the type of unit connected. Note also that
some units do not provide an "Auto" setting.
●
In the following cases, the actual air direction will differ from the direction
indicated on the remote controller display.
1. While the display is showing "STAND BY" or "DEFROST".
2. Immediately after starting heater mode (while the system is waiting for the
mode change to take effect).
3. In heat mode, when room temperature is higher than the temperature set-
ting.
Medium High
( ) ( )
→ 4 → 5
4 Downword airfrow 70°
5 Swing