Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
4. Weighing function (weight measurement only)
1. Switch on the scale by using the tap-on-function. For this tap with your foot
shortly on the centre of the scale. The display indicates the signal "0.0 kg". Now
the scale is ready to use.
2. Step on the centre of the scale. Remain stationary on the weighing platform and
do not you hold tight. After a few seconds your weight will be indicated.
3. After weighing step off the scale. The scale will automatically switch off after a
few seconds.
5. Programming / Enter of personal data
Before first-time use your personal data like gender (female or male), body height, age
and fitness level (A1 = no sport, A2 = occasional sport, A3 = regular sport, A4 = daily
sport, A5 = athlete) must be programmed and saved under selected locations 1 – 12
(up to 12 persons). The enter keys are located at the head front of the scale. To enter
your personal data please utilise the buttons:
(on button),
(minus button),
(plus button), SET (save button) and follow the
particular points:
1. Place the scale on a table. Switch on the scale by
using the
button. The display indicates "0.0 kg".
Then press the SET-button. The display indicates
flashing "01". To select your personal location (01-12)
press the or button. After the selection of your
personal location press the SET-button to save the
reading.
2. After you've selected your personal location (e.g. 03)
the symbol for gender starts to flash. To select the
requested gender ( female or
male), press the
or button. After the selection of your gender
press the SET-button to save the reading.
After you've selected your gender (e.g. female) the
3.
symbol for body height starts to flash (default 170cm).
To enter your height press the or button. After
the selection for your height press the SET-button
to save the reading.
4. After you've selected your body height the symbol
for age starts to flash (default Age 30). To enter your
age press the or button. After the selection of
your age press the SET-button to save the reading.
0.0
kg
30
170
Age
0.0
kg
30
Age
0.0
kg
4
5. After you've selected your age the symbol for fitness
level starts to flash (default A1). To enter your fitness
level (A1-A5) press the or button. After the
selection of your fitness level press the SET-button
to save the reading.
A few seconds after completion of the input the scale automatically powers off.
To enter personal data of further persons please repeat the steps listed below.
6. Body Analysis
An analysis is only possible in bare feet. Your personal data must be entered first
(please see page 4-5).
1. Step on the scale while the scale is powered off. The scale automatically will switch
on. The display passes through from the personal location 01 to personal location 12.
Step off the scale when the display indicates the selected location of your personal
data.
2. At the first time measurement the display indicates the signal „888" and a few
seconds later „0.0" kg. When you once used the scale the display indicates „888"
not anymore but the readings of your last measurement. This function allows you
to follow the changes between your measurements.
3. As soon as "0.0" kg appears on the display the scale is prepared for the
measurement.
0l
4. Carefully in bare feet step on the stainless steel strips on the right and left side of
the weighing platform and remain stationary while the measurement is now taking
place.
5. At first your weight will be indicated. Shortly after, while the analysis is taking place
03
the signal "
indicates as follows: weight, body fat, body water and BMI (body mass index).
EXAMPLE:
cm
F
23.8
03
56.4
Normal BMI range for men:
03
Normal BMI range for women:
Normal BMI for elder persons.
" start to move. After completion of the measurement the display
W
57.3
%
%
F =
W =
23.4
kg
BMI =
BMI
between 20 and 25
between 19 and 24
up to 26
5
30 170
Age
cm
03
0.0
kg
Body Fat %
Body Water %
Body Mass Index
Werbung
Kapitel
Inhaltsverzeichnis
