Body Analysis; Programming / Enter Of Personal Data - ADE BA 707 Petra Bedienungsanleitung

4. Weighing function (weight mea surement only)
1. Switch on the scale by using the tap-on-function. For this, tap with your foot shortly on
the centre of the scale. The display indicate the signal " 8888" and a few seconds later
" 0.0 kg" . Now the scale is ready to use.
2. Step on the centre of the scale. Remain stationary on the weighing platform and do
not hold you tight. After a few seconds, your weight will be displayed.
3. After weighing step off the scale. The scale will switch off automatically after a few
seconds.

5. Programming / Enter of personal data

Before first time use your personal data (gender: female or male, body height, age) must
be programmed and saved under selected locations 01 – 10 (up to 10 persons). The
enter keys are located at the head front of the scale. To enter your personal data please
ƒ
utilise the buttons: (minus button),
particular points:
1. Place the scale on a table. Switch on the scale by using
the tap-on-function. For this, tap with your hand shortly on
the centre of the scale. The display indicate the signal
" 8888" and a few seconds later 0.0 kg. Now press the
SET-button and the display indicate a flashing " 01" . To
select your personal location (01– 10), press the ƒor „
button. After the selection of your personal location press
the SET-button to save the reading.
2. After you selected your personal location (e.g. 03) the
symbol for gender starts to flash. To select the requested
gender (female or male), press the ƒor „-button. After the
selection of your gender press the SET-button to save the
reading.
3. After you selected your gender (e.g. female) the symbol for
body height starts to flash (default 170 cm). To enter your
heights press the ƒ or„-button. After the selection for
your height press the SET-button to save the reading.
4. After you selected your body height the symbol for age
starts to flash (default Age 30). To enter your age press the
ƒ or „-button. After the selection of your age press the
SET-button to save the reading.
„
(plus button), SET (save button) and follow the
8888
01
0.0
03
170
30
Age
4
After input completion, the display indicates again successively your entered personal data
until the display shows " 0.0 kg" . A few seconds later, the scale automatically powers off.
To enter personal data of further persons please repeat the steps listed below.

6. Body Analysis

An analysis is only possible in bare feet. Your personal data must be entered first (please
see page 4 - 5).
1. Switch on the scale by using the tap-on-function. For this, tap with your foot shortly on
the centre of the scale. The display indicates the signal " 8888" and a few seconds later
" 0.0 kg" . Press the SET-button and select your personal location by using the ƒ or „-
button.
2. At first your personal data will be displayed (age, body height and gender). Shortly after
that " 0.0 kg" will be indicated.
3. As soon as the display shows " 0.0 kg" the scale is prepared for the measurement.
4. Carefully step on the scale in bare feet and remain stationary while the measurement is
now taking place.
kg
5. At first, your weight will be indicated on the display. Shortly after, while the analysis is
taking place, the signals 1 –
measurement your weight, your body fat (F), your body water (H) and your muscle
mass ( ) will be shown successively 3 times.
6. After weighing step off the scale. The scale switches off automatically after a few
seconds.
kg
EXAMPLE:
71.2
kg
Weight
cm
The body fat content shows the amount in percentage of stored fat from the total weight
of a body. There is no generally accepted set value as this varies significantly according to
gender (due to the different build) and age. Body fat is vital for basic body functions. It' s
protecting organs, cushioning joints, regulating body temperature, storing vitamins and
serves the body as energy storage.
2 – 3 – 4 starts to move. After completion of the
F28.6 H45.7
% %
F = Body Fat H = Body Water
5
29.8
%
= Muscle Mass