Cleaning Instructions - World Dryer Warm Air DXA Betriebsanweisung Und Teile-Handbuch

World Dryer Operating Instructions and Parts Manual
World Dryer
E
N
G
General Safety Information
L
(Continued)
I
– To limit a voltage drop, and insure
S
efficient operation, use No. 12 wire
H
or larger as required by local or U.S.
National Electrical Code.
– Do not connect to a branch circuit
with CB or fuse protection over 20
Amps. This is in compliance with the
U.S. National Electrical Code #210-20.
– All automatic model hand dryers
must have a dedicated 20 Amp
circuit as required by Underwriters
Laboratories, Inc. (UL).
– Route all field wiring away from any
moving parts within the hand dryer.
CAUTION
Improper mounting of
this hand dryer could
result in personal injury or property
damage.
– Follow the mounting recommenda-
tions in Table 1.
– On a stud wall, one side of the hand
dryer should be mounted to an
existing stud.
Installation
FOR MODELS (D)A5, 52, 54, 548, 57
1. Disconnect the power source.
2. Use the security Allen wrench
supplied to remove the (2) cover
mounting screws. Remove the cover
from the dryer.
NOTE: When using surface mount wiring, an optional, available offset fitting #100BR must be ordered to adapt the wiring to
1/2" EMT.
Type of Wall
Hollow Tile, Lath, Wall Board or Metal
Cement, Brick, or Tile Covered Cement or Brick
Stud Wall with Wood Backing
Table 2
Warm Air Hand Dryers
™
3. Place the hand dryer base on the wall
at the desired location using Table 1
to determine the recommended
mounting height. With the base so
located, use it as a template to mark
locations of the 4 mounting bolt holes
on the wall. When two or more
dryers are installed, they should
be spaced 24" (61 cm) minimum
from center to center.
4. Fasten the base to the wall, using the
type of bolts suggested in Table 2.
5. Connect the dryer to the nearest
suitable distribution panel.
6. Replace cover, making certain not
to over-tighten cover bolts.
FOR AUTOMATIC DRYER
MODELS (D)XA5, 52, 54, 548, 57
1. Disconnect the power source.
2. Use the security Allen wrench
supplied to remove the (2) cover
mounting screws. Remove the
cover from the dryer.
3. Place the hand dryer base on the wall
at the desired location using Table 1
to determine the recommended
mounting height. With the base so
located, use it as a template to mark
locations of the 4 mounting bolt holes
on the wall. When two or more
dryers are installed, they should be
spaced 24" (61 cm) minimum from
center to center. Applies only to
the Automatic models: ensure that
Type of Bolt
1/4" (M6) Screw Type or Wing Type Toggle Bolts
1/4" (M6) Stud Type Expansion Bolts
No.16 (M8) Wood Screws
2
(D)XA and (D)A
no reflective object (such as a hand
basin) is located directly under the
infra-red sensor eye; the minimum
distance is 18 inches.
4. All automatic dryers must have their
own dedicated 20 amp circuit. This
is a UL-suggested requirement.
IMPORTANT: Consult local and
general regulations before performing
dryer installation. Ensure that the
electrical network is not overloaded.
Do not connect to a branch circuit
over 20 amps.
Maintenance
1. Remove fuse or shut off power to
the dryer at fuse box.
2. With security Allen wrench supplied
with dryer, remove two Allen screws
from bottom side of dryer case.
3. Remove dryer cover.

CLEANING INSTRUCTIONS

Read complete Instructions before
proceeding. Under normal use, cleaning
the Dryer once a year will keep it in
good operating condition. If the wash-
room traffic is heavier than normal,
the cleaning should be done every 6
months. Lint and dust build up inside
the dryer can result in damage to motor
and heating element as well as hot
emissions that could injure the user.
1. Turn off dryer at circuit breaker or
fuse panel.
Minimum Bolt Length
Dependent on wall thickness
3" (76 mm)
2 / " (70 mm)
3
4