Dtw250 Dtw251; Ec Declaration Of Conformity; Instruction Manual - Makita DTW250 Bedienungsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model
Capacities
Square drive
-1
No load speed (min )
Impacts per minute
Max. fastening torque
Overall length
Net weight
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for fastening bolts and nuts.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841:
Model DTW250
Sound pressure level (L
Sound power level (L
WA
Uncertainty (K) : 3 dB (A)
Model DTW251
Sound pressure level (L
Sound power level (L
WA
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841:
Model DTW250
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
h
Uncertainty (K) : 1.5 m/s
Model DTW251
Work mode : impact tightening of fasteners of the
maximum capacity of the tool
Vibration emission (a
h
Uncertainty (K) : 1.5 m/s
All manuals and user guides at all-guides.com
Standard bolt
High tensile bolt
D.C.14.4 V Model
D.C.18 V Model
) : 90 dB (A)
pA
) : 101 dB (A)
) : 94 dB (A)
pA
) : 105 dB (A)
2
) : 14.5 m/s
2
2
) : 11.0 m/s
2
DTW250
M10 - M16
M10 - M14
12.7 mm
0 - 2,200
0 - 3,200
230 N•m
165 mm
1.4 - 1.7 kg
D.C. 14.4 V
BL1415N / BL1430 / BL1430B / BL1440 / BL1450 / BL1460B
BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /
BL1840B / BL1850 / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
NOTE: The declared vibration emission value has
been measured in accordance with the standard test
method and may be used for comparing one tool with
another.
NOTE: The declared vibration emission value
may also be used in a preliminary assessment of
exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
4 ENGLISH
DTW251
M10 - M16
M10 - M14
12.7 mm
0 - 2,100
0 - 3,200
230 N•m
165 mm
1.5 - 1.8 kg
D.C. 18 V