Operation; Before Starting The Equipment; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL GE-PB 36/18 Li Originalbetriebsanleitung

The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Rated voltage: ......................... 18V DC / 36V DC
Caution!
The equipment is supplied without batteries and
without a charger and is allowed to be used only
with the lithium-ion batteries of the Power-X-
Change series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.

5. Before starting the equipment

5.1 Putting on the battery belt
1. Place the battery belt (Item 1) around your
hips.
2. Close the battery belt by pressing the prong
end of the buckle (Item 2) into the female end
of the buckle (Item 7).
3. Adjust the length of the battery belt with the
length-adjustment belt (Item 3) so that it rests
comfortably and securely on your hips.
5.2 Taking off the battery belt
Important! Always switch off a connected tool be-
fore you take off the battery belt. Otherwise there
is a risk of injury.
To take off the battery belt (including in an emer-
gency), press together the prongs (Item 2) and
pull them out of the female-end of the buckle.
5.3 Attaching the cables together
Wind the cable-ties (Item 8) on the removable
cable over the second cable and fasten the slot
on the "T" element of the cable-tie.
Anl_GE-PB_36-18_Li_SPK13.indb 11 Anl_GE-PB_36-18_Li_SPK13.indb 11
GB

6. Operation

You can use the battery belt with one PXC battery
(18V) or two PXC batteries (36V).
6.1 Using the battery belt with 1 PXC battery
To use the battery belt with only one PXC battery
(18V), remove the second battery mount (Item 5)
from the belt. To do so, press the pushlock button
(Item 5a) on the bottom side of the battery mount
and pull the battery mount up and off the belt.
6.2 Using the tool adapter
Push the tool adapter (Item 9) into the battery
mount provided on your cordless tool. Make sure
that the pushlock button (Item 9a) latches in
place. Observe the operating instructions issued
for the cordless tool. To remove the tool adapter,
press the pushlock button (Item 9a) and pull the
tool adapter off the cordless tool.
6.3 Using the hook
If required, e.g. when changing tools, you can
place the end of the cable from the tool adapter
(Item 9) in the hook (Item 6).
7. Cleaning, maintenance and
ordering of spare parts
Hazard!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
- 11 -
02.08.2021 10:40:07 02.08.2021 10:40:07