Fellowes Cambio Bedienungsanleitung Seite 2

SAFETY INSTRUCTIONS/WARNING
WARNING: IMPORTANT SAFETY INSTRUCTIONS – Read Before Using!
• CAUTION: Lift hazard! Two people are required to move desk. Serious injury may occur.
• DO NOT EXCEED MAXIMUM STATED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR.
• Do Not operate table if any part is damaged or defective.
• Do Not place obstacles in the desk's path.
• Do Not place objects under the desk that are taller than 558mm (22").
• Make sure the desk has proper clearance on all sides (at least 25mm (1")) to all surrounding
walls and objects.
• Do Not sit or stand on the desk.
• Do Not disassemble the legs, control box or controller. Serious injury may occur.
• Ensure all cord lengths are long enough to accommodate all changes in height and follow cord routing instructions in this manual. Failure to
follow these instructions may result in equipment damage or personal injury.
• Keep liquids away from all electrical components. Only clean electrical components with a dry cloth.
• For indoor use only.
• Keep power cord away from sources of heat.
• Unplug desk before moving or servicing.
• Remove all equipment and accessories from the desk before moving.
• Keep children away from moving parts and underneath the desk.
PARTS PROVIDED (Note: Extra hardware may be included)
A Crossbar x2
B Side Bracket x4
A
C Handset x2
D Foot x4
E Lifting Column x2
F Lifting Column x2
G Fixing Plate x2 +
Phillips Head Screw x4
H Control Box x2
I Connection Bar x2 E F
J Cable Management Tray x2
K Hook x4
L Power Cable x2
M M6x10 Hex Head Screw x16
N M6x16 Hex Head Screw x8
O Countersink Hex Head Screw x8
P M6 Phillips Round Head Screw x20
Q Phillips Head Screw x4
R Anti-Vibration Pad x20
S Cable Clip x6 K
L
T Hex Key x1
U M3 Phillips Head Screw x8
Additional Tools Required
Phillips Screw Driver
Power Drill
2
CambioBench_411659_RevB_10L_102219.indd 2-3
Cambio™ Height Adjustable Bench Base
Maximum Weight Including Table Top
≤ 100 kg
≤ 220 lbs
Technical Data
Voltage
Frequency
Current (Amps)
Wattage
B C
G H I J
M N O P Q R S
ENGLISH
INSTALLATION OF BASE
STEP 1
Attaching side brackets
• Place table face down on a soft, clean surface.
• Unpack the crossbar and carefully place it on the floor.
• Attach the side bracket to the end of the crossbar.
• Repeat the same process to assemble the other side brackets (x3).
*Note: Make sure the crossbar and side brackets remain facing down during installation.
STEP 2
Adjust the position of the frame before attaching it to the table
100-240V
• Adjust the cross channels to their final lengths.
50/60 HZ
• Use the Hex key to loosen the (8) set screws on the inward side of the cross channels.
5 Amps
• Check that the top supports on each side are aligned with the pre-drilled holes on frame.
200 Watts
• Once properly adjusted, use the Hex key to re-tighten the set screws (8 total).
D
STEP 3
Assemble the lift columns
• Remove the tabletop for further installation.
• Insert the two lifting columns into the two ends of the crossbar with the heads of the
lifting columns facing inward. Make sure the mounting holes in the lifting columns
completely align with the screw holes on the crossbar.
• Fix the lifting column and the side bracket with crossbar using 4 M6x10 Hex Head
screws with the Hex key.
T U
• Repeat the same process to assemble the other lifting column.
A
T
T
E/F
T
M
B
3
10/22/19 4:19 PM