Vares HV 220 Anwendungshinweise Seite 7

All manuals and user guides at all-guides.com
Cultivator carriages
LOADING INSIDE PLATFORM
TYPE CAPACITY DIMENSIONS, lxwxh
HV 220L 300 kg 1,270x950x300 mm
HV 220S 300 kg 1,270x950x300 mm
HV 350-7 350 kg 1,400x1,210x300 mm
HV 500-5 500 kg 1,370x1,040x300 mm
Tractor carriages
LOADING INSIDE DIM. OF THE
TYPE CAPACITY PLATFORM, lxwxh
TDK 300 kg 1,150X750X300 mm
TDKL 300 kg 1,150X750X300 mm
TR 220L 350 kg 1,270X950X300 mm
TR 220S 350 kg 1,270X950X300 mm
TR 220S TL 350 kg 1,270X950X300 mm
TR 500 - 5 500 kg 1,370x1,040x300 mm Braked with a press. brake
TR 350 - 7 350 kg 1,400x1,210x300 mm
TRVML 300 kg 1,150X750X300 mm
TRVMS 300 kg 1,150X750X300 mm
TRVMS TL 300 kg 1,150X750X300 mm
1 / Mounting the VARES semi-trailer (carriage)
Cultivator carriages:
a/ Turn the carriage platform upside down.
b / Insert the rear axle so that the flange for bolting-on the front drawbar would be directed to the front part of the
platform. Secure four M10x30 bolts, do not tighten them for the moment!
c / Bolt the front drawbar with four M10x30 bolts to the rear axle; do not tighten them for the moment! Secure the
front drawbar with the tipping mechanism.
d / Mount the travel wheels.
e / Pull the brake rope through the levers of the brake keys. At the zero position of the hand brake, slide on the
rope and ensure the rope clamps.
f / Turn the carriage on the wheels
g / Bolt on the seat with four M10x18 bolts. Level the seat before tightening the screws according to the front side
of the carriage.
h / Carefully tighten the bolts that connect the front drawbar and the rear axle and the bolts fastening the platform
(before that, level the seat so that it is perpendicular with respect to the platform!)
i / Release the tipping mechanism and bolt the safety chain.
j / Release the drawbar fitting and mount the carrier hinge. For tractor carriers, bolt the universal hinge so that
the carrier platform is in a horizontal position.
Tractor carriers:
For mounting the tractor carriers, the above-mentioned applies apart from the following: e. g.
2 / Preparation for driving
The driver's obligation is to carry out a routine check of the carriage before driving: The inspection primarily
concerns the pin of the platform tipping and tightening the threaded joints (primarily on the flange of the split
drawbar).
Check the brake in the cultivator carriages! When driving, brake only with the foot pedal! When stopped, the
trailer is secured against moving with the hand brake. Furthermore, it is convenient to secure the semi-trailer unit
by inserting a wedge under the wheel.
3 / Tires – For reliable operation and long-term service life of tires, the tire pressure must be maintained at a
prescribed value of 0.17 MPa.
4 / Driving manner – Driving with a semi-trailer (carriage) is normal; special driving properties of the semi-trailer
unit determines the towing unit. Be especially careful when reversing and turning. Various towing units with
different properties are designed for the trailer.
5 / Rear front – The rear front is tipping and removable. Two safety levers protect the platform against tipping
when driving.
6 / Seat – only for cultivator carriages. The seat is placed on the front part of the drawbar. Seat suspension is not
used in order to achieve a simple construction solution.
III. Technical data
TOTAL WIDTH X
TOTAL LENGTH
Braked 1,010x2,250 mm
Braked 1,050x2,250 mm
Braked 1,310x2,470 mm
Braked 1,360x2,470 mm
Not braked
Not braked
Not braked
Not braked
Not braked
Not braked
Not braked
Not braked
Not braked
IV. Instruction manual
Carriages VARES
TIRES
Tire pressure: 0.17 MPa
4.00-8 on bearings
145x70-8 on bearings
145x70-8 on bearings
165/70, R13 on bearings
155/70, R13
TOTAL TIRES
WIDTH Tire pressure: 0.17 MPa
810 mm 16X4/2pl on plastic rims
810 mm 4.00-8 on bearings
1 010 mm 4.00-8 on bearings
1 050 mm 145x70-8 on bearings
1 050 mm 16x6,5-8 on bearings
1 360 mm 165/70, R13 on bearings
1 310 mm 1,45x70-8 on bearings
810 mm 4.00-8 on bearings
850 mm 145x70-8 on bearings
850 mm 16x6,5-8 on bearings
7