Additional Safety And Working Instructions - Bosch Uneo Originalbetriebsanleitung

OBJ_BUCH-1695-002.book Page 10 Tuesday, April 2, 2013 10:59 AM
10 | English
 Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool's operation. If
damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
 Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
 Use the power tool, accessories and tool bits etc. in ac-
cordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
Battery tool use and care
 Recharge only with the charger specified by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fire when used with another bat-
tery pack.
 Use power tools only with specifically designated bat-
tery packs. Use of any other battery packs may create a
risk of injury and fire.
 When battery pack is not in use, keep it away from oth-
er metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
 Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addition-
ally seek medical help. Liquid ejected from the battery
may cause irritation or burns.
Service
 Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained.
Hammer Safety Warnings
 Wear ear protectors. Exposure to noise can cause hear-
ing loss.
 Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
or fastener may contact hidden wiring. Cutting accesso-
ry and fasteners contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
Additional Safety and Working In-
structions
 When transporting and storing, set the rotational di-
rection switch to the centre position. Danger of injury
when accidentally actuating the On/Off switch.
2 609 006 431 | (2.4.13)
All manuals and user guides at all-guides.com
 Use appropriate detectors to determine if utility lines
 When working with the machine, always hold it firmly
 Secure the workpiece. A workpiece clamped with clamp-
 For drilling without impact in wood, metal, ceramic and
 Inserting SDS-Quick Drilling Tools: Check the latching by
 The maximum torque is reached only in the screwdriving
 Replace a damaged dust protection cap immediately.
 Dusts from materials such as lead-containing coatings,
 Prevent dust accumulation at the workplace. Dusts can
 If the application tool should become blocked, switch
 When switching on with a blocked drilling tool, high
 Apply the power tool to the screw only when it is
 Always wait until the machine has come to a complete
 To save energy, only switch the power tool on when using
 Avoid unintentional switching on. Ensure the On/Off
 Do not open the battery. Danger of short-circuiting.
are hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age.
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
ing devices or in a vice is held more secure than by hand.
plastic, a suitable SDS-Quick tool or an application tool
with hexagon shank can be used.
pulling the tool.
operating mode (1. gear). The maximum no-load speed is
reached only in the operating modes drilling and hammer
drilling.
The dust protection cap largely prevents the penetration of
drilling dust into the tool holder during operation. When in-
serting the tool, pay attention that the dust protection cap
is not damaged.
some wood types, minerals and metal can be harmful to
one's health and cause allergic reactions, lead to res-
piratory infections and/or cancer. Materials containing
asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suita-
ble for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
easily ignite.
the machine off. Loosen the application tool.
torque reaction can occur.
switched off. Rotating tool inserts can slip off.
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
it.
switch is in the off position before inserting battery
pack. Carrying the power tool with your finger on the
On/Off switch or inserting the battery pack into power
tools that have the switch on invites accidents.
Bosch Power Tools