Description Of The Device; Using The Appliance; Cleaning And Maintenance - Camry Premium CR 7908 Bedienungsanweisung

19.Always use new batteries to replace the drained batteries in the remote control.
20.Do not move the device when the inner tank is filled with water.
21.Do not place any objects on the device.
22.The device can be used only with properly working ventilation.
23. To provide additional protection, it is advisable to install a residual current device (RCD)
in the electric circuit with a rated residual current not exceeding 30mA. Ask an electrician
for this.
Before first use
1. It should be remembered that a high level of humidity may favor the development of biological organisms in the environment.
2. Do not get wet the device or wet the area around the device. If moisture appears, reduce the efficiency of the humidifying function.
3. Do not allow absorbent materials such as carpets, curtains, tablecloths to get wet.
4. Never leave water in the tank when the device is not in use.
5. During filling and cleaning, disconnect the device from the mains.
6. Clean the device and water tank before using it again.
• WARNING: When the water is not replaced and the tank is not properly cleaned every 3 days, microorganisms that may be present in
the water or in the environment where the device is used or stored may develop in the water tank and be blown out to the surroundings.
This can cause a very serious health risk.
• WARNING: Every three days, empty the water tank and top up with clean water. Before refilling, clean the tank with fresh tap water or
using detergents. Remove any scale, deposits or film that has formed on the sides of the tank and on the interior surfaces. After
washing, wipe all surfaces dry.
DESCALING
1.Perform the descaling procedure in accordance with the instructions of the descaling agent specified by the manufacturer.
2.Use descaling agents intended for this purpose.
3. Carry out the descaling procedure at least every 3 months.
4. Descaling only the water tank with the device turned off.

DESCRIPTION OF THE DEVICE

1. Air outlet
4. Holder
7. Water tank
10. Two ice containers

USING THE APPLIANCE

A noticeable reduction in the temperature of the exhaust air occurs after putting into the water tank 2 plastic containers attached to the
product previously filled with water and frozen in the freezer. It is recommended to fill the tank with cold tap water.
1. After unpacking the device from the packaging, mount the wheels and place the device on a dry, flat surface, then connect the power
plug.
2. Slide out the water tank (7) on the back of the machine and pour in the water. Be careful not to exceed the maximum level.
3. Turn on the device with the 8.4 button on the control panel or remote control. Manual operation of the device is identical to operation
via a remote control.
8.1 - Air speed adjustment button: slow, medium, fast.
8.2 - The button reduces the temperature of the air by activating the water pump. Two ice containers (10) are included in the set. To use
them, fill them with tap water up to ¾ height and freeze. Then insert one or both of them into the water tank (7). In order to blow
out cool air, there must be water inside the tank (7). During operation, periodically check the water level and add water. Turning
on the button simultaneously activates the air humidification function.
8.3 - The button causes oscillation of vertical louvers that ensure even distribution of the cooled air stream. The horizontal blinds do not
move automatically - you can move them manually.
8.4 - Button for switching the device on and off.
8.5 - The button allows you to change the blower mode. In addition to the normal mode, "NATURE" and "SLEEP" are available.
"NATURE" mode imitates the action of natural wind by changing the blower speed about every 10 seconds and successively
changing the speed of the blower between slow, medium to fastest. On the other hand, setting the "SLEEP" mode will result in
the device switching off after a specified time. If we set the slow speed, the device will turn off automatically after 30 minutes. If
we set the medium speed, after 30 minutes the device will reduce the speed to slow, and after another 30 minutes it will turn off
automatically. If we set the fastest speed, the device after 30 minutes will reduce the speed to medium, then after another 30
minutes it will slow down slowly, and after another 30 minutes it will turn off automatically.
8.6 - The display shows the room temperature level.
8.7 - The button allows you to program the operation time of the device from 1 to 12 hours. If you don't use button 8.7, the device will
work until you turn it off manually.
8.8 - The button turns off the control panel lighting.
4. To end the operation of the device, switch off the device with the 8.4 button.

CLEANING AND MAINTENANCE

It is recommended to clean the device with a soft, dry cloth. Do not use any chemical solvents as they may permanently damage or
deform the surface. If the device will not be used for three months or longer, remove the batteries from the remote control. Pour
water out of the tank before storage. Dry the device to avoid moisture damage. Set the 8.1 button to the highest fan speed, the
2. Water level indicator
5. Filter mesh
8. Control panel
3. Wheels
6. Power cord
9. Remote control
4