Search And Edit Channels; Child Protection/Password (Pin Code); Factory Defaults; Changing Time Settings - AEG DVBT 4538 Bedienungsanleitung, Garantie

AEG_BDA_DVB_T4538_GB_ka1.qxd:CL_BDA_DVB_T776_GB_ka.qxd

Search and edit channels

In order to quickly search a channel or to change
the features of saved channels, select the
"SETUP/Installation" submenu.
Automatic channel search (Auto/Scan):
Start the automatic channel search with the "red"
button.
Press the "OK" key.
All available channels will be searched and stored in
a programme slot.
Manual search (Manual Scan):
The individual settings for a station can be carried
out in this menu.
For this method, it is necessary to know the sear-
ched-for programme's channel number, frequency
and bandwidth.
Press the "green" button to call up the "Manual
Scan" menu.
For changing the settings, use the "
" VOL+" arrow buttons.
After having carried out all settings, the search
run is activated by pressing the "OK" button.
All channels found in the area will be stored in a
programme slot.
Child Protection/Password
(PIN code)
In the "Password", you can carry out the following
settings:
• the "Menu Lock",
• set the "channel lock" (child lock),
• set the "censorship lock",
• changing the password.
Menu Lock
In this menu you can set whether the password has
to be entered in order to call up the SETUP menu.
Child Lock
In the "TV/TV List" menu (see page 40) you can
block individual channels. With the "channel lock"
function you can switch this lock on and off.
If you would like to switch on the child lock,
select the "on" option.
If you would like to switch off the child lock,
select the "off" option.
Censorship Lock
In this menu you can choose between:
• "No block"
• "Total block" = all channels and some menu
options can only be released after the password
has been entered.
• „2" to „18" = Here you can determine the des-
ired age rating. This function must be supported
by the channel, which must transmit appropriate
data.
Changing the password
You may change the password (PIN code) set in the
factory and enter any other four-digit number as
your personal PIN code. The password "6666" has
been pre-programmed in the factory.
Note your new password; once changed, only
the new code is valid for all password queries.
If you've forgotten your personal password, you
can assign a new password by means of the
master password "1307".
Enter the old password (PIN) using the numercal
keys.
Enter the new password using the numercal keys.
Enter the new password again.
The information window "PIN code changed" appe-
VOL-" and
ars.
Press the 'OK' key to confirm.
The new password is integrated.

Factory defaults

The receiver is reset to its condition on delivery.
All of your settings and stored data are deleted.
Select the "Set Default" submenu in the
"SETUP" menu by using the "▼ CH-" and
"▲ CH+" arrow buttons.
Press the 'OK' key to confirm.
You will be prompted to confirm your selection.
Press the "OK" button if you would like to return
the receiver back to the factory settings.
Press the "EXIT" button if you would like to exit
the menu.
Wait until the receiver re-starts.
This process may take a few minutes. The instal-
lation menu then appears.
Press the "EXIT" key to return to the TV channel.

Changing time settings

In the "SETUP/Installation" menu you can determi-
ne the "time zone". Adjust the "time zone" relative to
the main time zone (GMT) according to where you
live.
The "time zone" can only be set if the "Off"
option in the "Auto time zone" menu is selec-
ted.
16.04.2009 10:48 Uhr Seite 39
39