PCE Instruments PCE-SDL1 Bedienungsanleitung Seite 7

5. 3 Data log gger use
Co omply with the operat
Op perating n notes
• In norm mal mode (N
average e of these s
are take en from the
• In peak k mode (PEA
whole m measureme
• First set up p the data l
display. Se et 'LED flash
checkbox.
• Remove th he datalogg
• Place the d device in a
specificatio ons for allo
install the windscreen
• When the datalogger
until the g green LED (
will flash e every 10 se
Setup).
• When the sound leve
enabled in n the Alarm
• To end ma anual recor
six times. Recording
• When data alogger me
will stop re ecording an
• To downlo oad the data
protective cover (1)
• To see a ta able of the
• Refer to th he help-fun
informatio on on down
• When the battery bec
battery.
Note: whe en battery
6. . Battery y replace
Re efer to the i illustrations
• T The datalog gger contai
• T To replace the battery
• ( (A) Open t he battery
pointed obj p ject in the d
• ( (B) Gently pull the da
• ( (C) Remov ve/insert the
i ndicated in n the casing
• ( (D) Slide th he data log
using the e u nclosed sof
No ote: leaving g the devic
WAR RNING:
Do n not punctu
awa ay from ch
7. . Technic cal speci
a ccuracy
fr requency ra ange
d ynamic ran nge
measuring r m range
d ata memor ry
sa ampling rat te
fr requency w weighting
ti me weighti ing
microphone m
16/ /12/2010
ing conditio ons as indic
NORM) gro ups of 20 s
samples is stored. Te
ese 20 sam mples.
AK) data is s measured
ent.
logger via t the software
h cycle' to 10, 20 or 3
ger from th e USB slot
location w here record
owed opera ting tempe
n (9) to av void false re
r is set up t to start ma
(6) flashes six times.
econds (inc rease this v
el crosses th he set Alar
Setup and d the LED f
ding, press s and hold t
has stoppe ed and the
mory is ful l or the pre
nd the yello ow LED (5)
a into the p personal co
and plug t he datalogg
data, click k (g); t
nction of the e datalogge
loading and d handling
comes low, , both red (
becomes lo ow, the late
ement
s on page 2 2 of this ma
ns a non-re echargeable
y, disconnec ct the devic
compartme ent by usin
direction of f the arrow
ata logger f from the ca
e battery. O Only use 3
g.
gger back in n the housi
ftware.
ce in the US SB port will
ure or thro ow batteri
hildren.
fications s
± 1.4d
31.5Hz
50dB
30dB t
129920
1s ~ 2
A, C
fast (1
1/2" el
PCE-SDL1
cated in §7 7.
samples are e taken (on
maximum (Pmax) and
d every 50m ms. The Pm max and Pm
e (refer to §5.2). For
0s and che ck the 'LED
and replac ce the prote
ding of sou nd level is
erature and humidity r
eadings.
nually (dela ayed start)
The datalo gger starts
value or dis sable LED o
m Low or A Alarm Hi lev
flash cycle i is not set to
the Start b button (3)
yellow LED D (5) flashe
eset numbe er of sampl
) will also fl lash once e
mputer, st art the data
ger into a f free USB-sl
o print it, c click (i).
er software e ('Help'
the data fr om the dat
(5) and gre een (6) wil
est 1.5h of data are lo
anual.
e 3.6V Lith ium battery
ce from the e computer
ng a pointed d object (e
.
asing.
3.6V Lithiu um batteri
ng until it s snaps into
reduce the e battery lif
ies in fire as they m might explo
B
z to 8kHz
o 130dB
0
4h
25ms), slow w (1s)
ectret cond denser micr
7
ne reading e every 50m
d minimum m (Pmin) pe
in are thos
ease of use e enable the
D flash for H Hi and Lo al
ective cove r (1).
required. R Refer to the
range. In w windy enviro
, press the Start butt
s logging an nd the gree
output via t the LED Fla
vel, the red d LED (5) f
o 'No Light' '.
±3s until th he red LED
es once eve ery 10s.
ing points i is reached,
every 10s.
alogger sof ftware, rem
ot. Click th e download
. To print th he graph, c
'Help topics s ...') for m
talogger.
l flash. Ref fer to §7 to
ost
y.
r.
.g. small sc crewdriver)
ies. Make s sure the po
place. Conf figure the d
fe.
ode. Keep
rophone
s) and the
eak values
se of the
e LED statu us
arm'
e technical
onments,
ton (3) ±3 s
en LED (6)
ash Cycle
flashes whe en
(5) flashe es
the logger r
move the
d button .
click (h) ).
ore
o replace th he
). Move the e
olarity is as
data logger r
batteries