Dry Pick-Up; After Using The Machine; After Use; Transport - Conel CLEAN M30 Bedienungsanleitung

Put back the motor top to the container. Secure the
motor top with the latches.
Heavy maneuvers can, by mistake, trigger the water
level limiting device. Should this happen; turn off the
machine and wait for 3 seconds to reset the device.
Continue to operate the machine afterwards.
3.8

Dry pick-up

CAUTION
Picking up environmentally hazardous materi-
als.
Materials picked up can present a hazard to
the environment.
• Dispose of the dirt in accordance with le-
gal regulations.
Remove the electrical plug from the socket before
emptying after dry pick-up. Remove the suction hose
from the machine and close the inlet cap, to avoid
harmful dust spreading. Release the latch by pulling
them outwards so that the motor top is released. Lift
up the motor top from container.
Main Filter: check the filter. To clean the filter you
can either brush or wash it. Wait until the filter is dry
before re-starting dust pick-up.
Dustbag: check bag to ensure the fill factor. Re-
place dust bag if necessary. Remove the old bag.
The new bag is fitted by passing the carboard piece
with the rubber membrane through the vacuum inlet.
Make sure that the rubber membrane is passing past
the heightening at the vacuum inlet.
After emptying: close motor top to the container
and secure the motor top with the latches. Never
pick up dry material without filter fitted in the ma-
chine. The suction efficiency of the machine de-
pends on the size and quality of the filter and dust
bag. Therefore - use only Original filter and dust
bags.
4

After using the machine

4.1

After use

After picking up hazardous dust, close the inlet cap
and clean the outside of the machine.
Remove the plug from the socket when machine is
not in use. Wind up the cord starting from the ma-
chine. The power cord can be wound up around the
motor top or at the container or placed in the includ-
ed hook, or fastening means. Some variants have
special storage places for accessories.
4.2

Transport

• Before transporting the machine, close all the
latches.
• Close the inlet with the inlet cap.
• Do not tilt the machine if there are liquids in the
dirt tank.
• Do not use a crane hook to lift the machine.
• Do not lift the machine by the trolley handle *)
20 OEL=Occupational Exposure Limit,
1)
4.3

Storage

CAUTION
Store the appliance in a dry place, protected
from rain and frost. The machine shall be
stored indoors only.
4.4

Accessory and tool storage

For convenient transport and storage of accesso-
ries or tools, integrated rails are found on side of
machine which allows fastening with straps or other
means. A flexible strap and hooks are included on
back of machine for attachment of suction hose or
mains cable. For instruction see quick reference
guide.
An optional adapter plate with attachment system
*)
can be installed on top of machine for fastening of
2-point or 4-point storage cases.
Remove the electrical plug from the socket before
installing the adapter plate.
CAUTION
Do not lift machine in adapter plate without
having storage case safely installed. Note the
weight and balance of the appliance in case of
storage. Maximum weight of storage cases is
30 kg.
4.5

Recycling the machine

Make the old machine unusable.
1. Unplug the machine.
2. Cut the power cord.
3. Do not discard of electrical appliances with
household waste.
As specified in European Directive 2012/19/EU
on old electrical and electronic appliances,
used electrical goods must be collected sepa-
rately and recycled ecologically.
5

Maintenance

5.1

Regular servicing and inspection

Regular servicing and inspection of your machine
must be carried out by suitably qualified personnel in
accordance with relevant legislation and regulations.
In particular, electrical tests for earth continuity, in-
sulation resistance, and condition of the flexible cord
should be checked frequently.
In the event of any defect, the machine MUST be
withdrawn from service, completely checked and
repaired by an authorized service technician.
At least once a year, a conel technician or an in-
structed person must perform a technical inspection
including filters, air tightness and control mecha-
nisms.
5.2 Maintenance
Remove the plug from the socket before performing
maintenance. Before using the machine make sure
Optional accessories / Option depending on model
*)
*)
Original instruction