Preparation For Operation; Operation / Settings - VERTO 50G139 Betriebsanleitung

Explanation of used symbols
1 2
5 6
1. Read instruction manual, observe warnings and safety conditions
therein!
2. Protection class 2.
3. Protect from humidity and rain.
4. The charger is designed to operate indoors in dry environment.
5. Do not allow to heat above 50°C.
6. Do not throw cells into fire.
7. Hazardous to water environment.
8. Recycling.
CONSTRUCTION AND USE
You can use the cordless screwdriver with a variety of short driver bits
with hexagonal shaft sized 6.35 mm (1/4"). The screwdriver features clip
(drum) with 10 driver bits and allows for automatic change of the bit.
The tool is designed mainly as a screwdriver, it can also be used with
sockets and drills with hexagonal holders (6.35 mm) for light drilling
tasks (e.g. making of pilot holes). Cordless, battery-powered power
tools are especially useful for works in interior furnishing, adaptation of
premises etc.
Use the power tool in accordance with the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Tool holder
2. Preview window for driver bit selection
3. Slider for driver bit replacement
4. Direction selector switch
5. Socket for charger
6. Battery level indicator (LED)
7. Switch
8. Illumination (LED)
9. Drum for driver bits
* Differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Charger
2. Soft bag
3 4
7 8
- 1 pce
- 1 pce
10

PREPARATION FOR OPERATION

BATTERY CHARGING
The screwdriver is supplied with partially charged battery. It is
recommended that the first charging last for 2 hours. Charge the battery
in ambient temperature between 4°C and 40°C.
• Insert the charger cord plug into the socket for charger (5) located in
the screwdriver casing (fig. A).
• Connect the charger to mains socket 230 V AC.
• The battery level indicator (6) on the screwdriver casing turns on to
inform that the charging is in progress. At first one diode turn on, then
next diodes light up as the charging progresses.
Battery level indicator LEDs (6) stay turned on through whole charging
process and afterwards, until the charger is disconnected from mains
socket.
BATTERY LEVEL INDICATION
The device is equipped with indication of the battery level (3 LED diodes)
(6). Press the switch button (7) in order to check the battery level. When
all diodes are lit, the battery level is high. When 2 diodes are on, the
battery is partially discharged. When only one diode is lit, the battery is
discharged and must be recharged.
Normal use of the screwdriver battery allows for multiple chargings. To
maintain the screwdriver in good condition, recharge its battery at least
once per six months.
Normal use of the screwdriver battery allows for multiple chargings.
To maintain the screwdriver in good condition, recharge its battery
at least once per six months.
Battery heats up strongly when charging. Do not operate just after
charging – wait for the battery to cool down to room temperature. It
will prevent battery damage.

OPERATION / SETTINGS

SWITCHING ON / OFF
Switching on – press the switch button (7).
Switching off – release pressure on the switch button (7).
ILLUMINATION
Each time the switch button (7) is pressed, the LED diode (8) lights up to
illuminate the workplace.
EXTENDING DRIVER BIT
• Set the direction selector switch (4) in the middle position.
• Rotate and set the drum for driver bits (9) to required bit. Use the
preview window for driver bit selection (2) (fig. B).
• Press the button of the slider for driver bit replacement (3) and slide
it forward (fig. C).
REPLACEMENT OF DRIVER BIT
• Set the direction selector switch (4) in the middle position.
• Press the button of the slider for driver bit replacement (3) and slide
it back (fig. D).
• Rotate the drum for driver bits (9) to set it to required bit and repeat
actions described above.
Each extended driver bit can be removed from the tool holder (2) and
replaced with another working tool only when the slider for driver bit
replacement (3) is set to forward position.
RIGHT-LEFT DIRECTION OF ROTATION
Use the direction selector switch (4) to choose direction of spindle
rotation (fig. E).
Clockwise rotation – set the direction selector switch (4) to the extreme
left position.
Counter-clockwise rotation – set the direction selector switch (4) to
the extreme right position.
* In certain cases position of the direction selector switch relating to rotation direction
may be different than specified. Please refer to graphic signs located on the switch or
tool body.
Safe position of the direction selector switch (4) is in the middle, it
prevents accidental starting of the power tool.