Makita HR006G Betriebsanleitung Seite 14

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Side handle
► Fig.8
CAUTION:
Use the side handle only when chip-
ping, scaling or demolishing. Do not use it when
drilling in concrete, masonry, etc. The tool cannot be
held properly with this side handle when drilling.
► Fig.9: 1. Side handle 2. Clamp nut
The side handle can be swung in a vertical direction and secured at
any desired position. It can also be adjusted at eight steps back and
forth in a horizontal direction. Loosen the clamp nut to swing the side
handle to a desired position, and then tighten the clamp nut securely.
Side grip (auxiliary handle)
CAUTION:
Always use the side grip to ensure
safe operation.
CAUTION:
After installing or adjusting the side
grip, make sure that the side grip is firmly secured.
The side grip can be swung, allowing easy handling of the tool in any
position. Loosen the side grip by turning it counterclockwise, swing it
to the desired position and then tighten it by turning clockwise.
► Fig.10: 1. Side grip
Installing or removing drill bit
Grease
Clean the shank end of the bit and apply grease before
installing the bit.
Coat the shank end of the bit beforehand with a small
amount of grease (about 0.5 - 1 g). This chuck lubrica-
tion assures smooth action and longer service life.
► Fig.11: 1. Shank end 2. Grease
Insert the drill bit into the tool. Turn the drill bit and push
it in until it engages.
After installing the drill bit, always make sure that the
drill bit is securely held in place by trying to pull it out.
► Fig.12: 1. Drill bit
To remove the drill bit, pull the release cover down all
the way and pull the drill bit out.
► Fig.13: 1. Drill bit 2. Release cover
Chisel angle (when chipping,
scaling or demolishing)
The chisel can be secured at the desired angle. To change
the chisel angle, rotate the action mode changing knob to
the symbol. Turn the chisel to the desired angle.
► Fig.14: 1. Action mode changing knob 2. Pointer
Rotate the action mode changing knob to the
sure that the chisel is securely held in place by turning it slightly.
Depth gauge
The depth gauge is convenient for drilling holes of
uniform depth.
Press and hold the lock button, and then insert the
depth gauge into the hex hole.
► Fig.15: 1. Depth gauge 2. Lock button
Make sure that the toothed side of the depth gauge
faces the marking.
► Fig.16: 1. Marking 2. Toothed side
Adjust the depth gauge by moving it back and forth
while pressing the lock button. After the adjustment,
release the lock button to lock the depth gauge.
NOTE: Make sure that the depth gauge does not
touch the main body of the tool when attaching it.
Dust extractor attachment
Optional accessory
Installing the dust extractor
attachment
1.
2.
cover fit in the grooves between the tool and the side
grip.
► Fig.17: 1. Dust cover 2. Claw 3. Groove
3.
4.
for your work. When you use bellows, attach the joint to
its top. When you stack two bellows, connect them with
the joint.
► Fig.18: 1. Dust cover extension 2. Dust cover
Connecting the tool to the vacuum
cleaner
1.
the hose holder to the holder joint.
► Fig.19: 1. Holder joint 2. Hose holder
NOTE: The hose joint can be attached to either side
of the tool.
only for attaching the holder joint.
Using the mounting part for any other purpose may
cause an unexpected accident.
2.
► Fig.20: 1. Hose holder
NOTE: Use joint 25 to connect the hose and the dust
cover if necessary.
Using depth gauge for drilling
operation
When you stack two bellows, attach the depth gauge
symbol. Then make
extension to the depth gauge.
► Fig.21: 1. Depth gauge extension
14 ENGLISH
Loosen the side grip on the tool.
Install the dust cover so that the claws of the dust
Tighten the side grip securely.
Set the suitable bellows or dust cover extension
3. Joint 4. Bellows
Attach the holder joint to the tool, and then attach
WARNING:
Use the mounting part of the tool
Fix the hose to the hose holder.