Herunterladen Diese Seite drucken

Safety Information - Axis Q6100-E Installationsanleitung

Vorschau ausblenden Andere Handbücher für Q6100-E:

Werbung

English

Safety information

Hazard levels
DANGER
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NO TICE
TICE
NO
NO
TICE
Indicates a situation which, if not avoided, could result
in damage to property.
Other message levels
Important
Indicates significant information which is essential for
the product to function correctly.
Note
Indicates useful information which helps in getting
the most out of the product.
Safety instructions
NO TICE
NO
NO
TICE
TICE
The Axis product shall be used in compliance with
local laws and regulations.
Store the Axis product in a dry and ventilated
environment.
Avoid exposing the Axis product to shocks or heavy
pressure.
Do not install the product on unstable poles,
brackets, surfaces or walls.
Use only applicable tools when installing the Axis
product. Using excessive force with power tools
could cause damage to the product.
Do not use chemicals, caustic agents, or aerosol
cleaners.
Use a clean cloth dampened with pure water for
cleaning.
Use only accessories that comply with the technical
specification of your product. These can be provided
by Axis or a third party. Axis recommends using
Axis power source equipment compatible with your
product.
Use only spare parts provided by or recommended
by Axis.
Do not attempt to repair the product yourself.
Contact Axis support or your Axis reseller for
service matters.
Do not point the camera lens toward the sun or
other high-intensity radiation sources because this
could cause damage to the camera.
The power supply shall be plugged in to a socket
outlet installed near the product and shall be easily
accessible.
Use a limited power source (LPS) with a rated
output power limited to ≤100 W and a rated output
current limited to ≤5 A.
Use a yellow/green colored grounding cable of at
2
least 2.5 mm
or 12 AWG.
Transportation
NO TICE
TICE
NO
NO
TICE
When transporting the Axis product, use the
original packaging or equivalent to prevent damage
to the product.
Battery
The Axis product uses a 3.0 V BR/CR2032 lithium
battery as the power supply for its internal real-time
clock (RTC). Under normal conditions this battery will
last for a minimum of five years.
CAUTION
Do not replace the battery yourself. Contact Axis
support if the log message requests a battery change.
Lithium coin cell 3.0 V batteries contain
1,2-dimethoxyethane; ethylene glycol dimethyl ether
(EGDME), CAS no. 110-71-4.
Dome cover
NO TICE
TICE
NO
NO
TICE
Be careful not to scratch, damage or leave
fingerprints on the dome cover because this could
decrease image quality. If possible, keep the
protective plastic on the dome cover until the
installation is complete.
Do not clean a dome cover that looks clean to
the eye and never polish the surface. Excessive
cleaning could damage the surface.
For general cleaning of the dome cover it is
recommended to use a non-abrasive, solvent-free
neutral soap or detergent mixed with pure water
and a soft, clean cloth. Rinse well with pure
lukewarm water. Dry with a soft, clean cloth to
prevent water spotting.
Never use harsh detergents, gasoline, benzene,
acetone, or similar chemicals.
Avoid cleaning the dome cover in direct sunlight or
at elevated temperatures.
Make sure the dome is attached in operation mode,
otherwise focus may be affected.
Français
Informations sur la sécurité
Niveaux de risques
DANGER
Indique une situation dangereuse qui, si elle n'est pas
évitée, entraînera le décès ou des blessures graves.
AVERTISSEMENT
Indique une situation dangereuse qui, si elle n'est pas
évitée, pourrait entraîner le décès ou des blessures
graves.
ATTENTION

Werbung

loading