Intended Use; Safety Information - KRAFT WERKZEUGE 7110 Originalbetriebsanleitung

Intended use

The compressor is designed to generate com-
pressed air for compressed-air driven tools which
can be driven with a theoretical air intake capacity
180 l/min (e.g. tire infl ator, blow-out pistol and paint
spray gun). Due to the limited air output it is not pos-
sible to use the compressor to drive tools with very
high air consumption (for example orbital sanders,
rod grinders and hammer screwdrivers).
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufac-
turer will be liable for any damage or injuries of any
kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.

Safety information

m Attention! The following basic safety
actions must be taken when using this
compressor in order to protect the user
from electric shocks and the risk of injury
and fi re. Read and follow these instruc-
tions before using the equipment.
Safe work
Keep the work area orderly
1
Disorder in the work area can lead to
–
accidents.
Take environmental influences into ac-
2
count
Do not expose electric tools to rain.
–
Do not use electric tools in a damp
–
or wet environment. There is a risk of
electric shock!
Make sure that the work area is well-
–
illuminated.
Do not use electric tools where there
–
is a risk of fire or explosion.
Protect yourself from electric shock
3
Avoid physical contact with earthed
–
parts (e.g. pipes, radiators, electric
ranges, cooling units).
Keep children away
4
Do not allow other persons to touch
–
the equipment or cable, keep them
away from your work area.
Securely store unused electric tools
5
Unused electric tools should be stored
–
in a dry, elevated or closed location
out of the reach of children.
Do not overload your electric tool
6
They work better and more safely in
–
the specified output range.
14 14 GB
Wear suitable clothing
7
Do not wear wide clothing or jewellery,
–
which can become entangled in mov-
ing parts.
Rubber gloves and non-slip shoes are
–
recommended when working out-
doors.
Tie long hair back in a hair net.
–
Do not use the cable for purposes for
8
which it is not intended
Do not use the cable to pull the plug
–
out of the outlet. Protect the cable
from heat, oil and sharp edges.
Take care of your tools
9
Keep your compressor clean in order
–
to work well and safely.
Follow the maintenance instructions.
–
Check the connection cable of the
–
electric tool regularly and have it
replaced by a recognised specialist
when damaged.
Check extension cables regularly and
–
replace them when damaged.
Pull the plug out of the outlet
10
During non-use of the electric tool
–
or prior to maintenance and when
replacing tools such as saw blades,
bits, milling heads.
Avoid inadvertent starting
11
Make sure that the switch is switched
–
off when plugging the plug into an
outlet.
Use extension cables for outdoors
12
Only use approved and appropriately
–
identified extension cables for use
outdoors.
Only use cable reels in the unrolled
–
state.
Remain attentive
13
Pay attention to what you are doing.
–
Remain sensible when working. Do
not use the electric tool when you are
distracted.
Check the electric tool for potential
14
damage
Protective devices and other parts
–
must be carefully inspected to ensure
that they are fault-free and function
as intended prior to continued use of
the electric tool.
Check whether the moving parts
–
function faultlessly and do not jam or
whether parts are damaged. All parts
must be correctly mounted and all
conditions must be fulfilled to ensure
fault-free operation of the electric
tool.
Damaged protective devices and
–
parts must be properly repaired or
replaced by a recognised workshop,