Adjusting The Table Top Height; Saving A Memory Position; Additional Information; Disassembly - Swedstyle Memory S Handbuch

10 Swedstyle Memory - EN

5.1 Adjusting the table top height

CAUTION. Risk of minor or moderate injury through crushing
Your fingers may be crushed when you attempt to change the height of the table
• Keep fingers away from moving parts
• Ensure that no persons or objects are in the table's range of motion
INFO The Table Top will move up or down until the UP or DOWN Key is released,
or if a pre-defined stopping point has been reached.
To move the Table Top UP:
Press and hold until the desired height has been reached
To move the Table Top DOWN:
Press and hold until the desired height has been reached
4.4 Advanced Functions
4.4.1 Storing a position

5.2 Saving a memory position

Using this function you are able to store a desk-height.
This function saves a set Table Top position. One Memory Position can be saved
Note: On initial operation all stored positions are equal to the lowest
possible desk-height (lower end position).
per Memory Position Key.
Note: Only one desk-height per button is allowed.
1. Move the table to the desired height
1.
Move the desk to the position you want to store.
2. The display shows the Table Top height (e.g. 73 cm)
The display reads the actual height of the desk (e.g. 73cm).
3. Press the SAVE Key
2.
S Press the S button.
The display reads S –.
4. Press the Memory Position Key (e.g. 2)
3.
Press the position button of choice (e.g. S2).
5. The display shows S 2
The display reads S 2.
4.
Now the height is stored on the chosen position button.
6. After about two seconds, the Table Top height is displayed again
The saving operation is confirmed with a double-click sound and after
approximately 2 seconds the stored height will be displayed.
6

ADDITIONAL INFORMATION

6.1 Disassembly

To disassemble your Handset, ensure that it has been disconnected from the Power Unit.
Then, follow the assembly instructions in reverse order.

6.2 Maintenance

The handset is maintenance-free for their entire service lifetime.
4.4 Advanced Functions
4.4.1 Storing a position
Using this function you are able to store a desk-height.
Note: On initial operation all stored positions are equal to the lowest
possible desk-height (lower end position).
Note: Only one desk-height per button is allowed.
4.4 Advanced Functions
1.
4.4.1 Storing a position
Move the desk to the position you want to store.
Using this function you are able to store a desk-height.
The display reads the actual height of the desk (e.g. 73cm).
2.
Press the S button.
Note: On initial operation all stored positions are equal to the lowest
possible desk-height (lower end position).
The display reads S –.
3.
Press the position button of choice (e.g. S2).
Note: Only one desk-height per button is allowed.
The display reads S 2.
4.
Now the height is stored on the chosen position button.
1.
Move the desk to the position you want to store.
The saving operation is confirmed with a double-click sound and after
The display reads the actual height of the desk (e.g. 73cm).
approximately 2 seconds the stored height will be displayed.
2.
Press the S button.
The display reads S –.
3.
Press the position button of choice (e.g. S2).
The display reads S 2.
4.
Now the height is stored on the chosen position button.
The saving operation is confirmed with a double-click sound and after
approximately 2 seconds the stored height will be displayed.
Page 9 / 12
Page 9 / 12
Page 9 / 12
WARNING. Risk of death or serious injury through electric shocks and other hazards
Using a Handset alongside unauthorized spare or accessory parts may lead
to death or serious injury through electric shocks and other hazards.
• Only use accessory parts produced or approved by Swedstyle
• Only use replacement parts produced or approved by Swedstyle
• Only allow Skilled Persons to perform repairs or install accessory parts
• Contact customer services immediately if the system malfunctions
The use of unauthorized spare or accessory parts may cause system damage. Warranty
claims are void in this scenario.

6.3 Cleaning

1. Disconnect the height-adjustable desks power supply from the power source.
2. Wait 30 seconds for residual voltage to dissipate.
3. Wipe the surface of the Handset with a dry soft cloth or a soft cloth lightly moistened
in water. Never immerse the Handset into any liquid.
4. Wait for the Handset to dry completely.
5. Reconnect the power supply.
6.4

Replacing a handset

1. Disconnect the Control Box from the Mains.
2. Disconnect the Handset from the Control Box.
3. Remove the Handset from the Table Top.
4. Mount the new Handset onto the Table Top.
5. Plug the Handset back into the Control Box.
6. Reconnect the Control Box to the Mains.

6.5 Troubleshooting

Usually, malfunctions occur when Handsets are pressed while calibrating. If the Handset fails to
function, you will need to restart the system. To do this:
1. Unplug the Handset from the Control Box.
2. Plug the Handset back to the motor Control Box.
3. After a few seconds the Handset is ready for operation.
A list of common problems and their solutions can be found in the Operating Manual
of the installed Control Box.

6.6 Disposal

Dispose of all components separately from household waste. Use designated collection
points or disposal companies authorized for this purpose
Swedstyle Memory - EN 11