VONROC VC504AC Bersetzung Der Originalbetriebsanleitung Seite 9

11. Press the power switch (1) into the " OFF/0"
position to switch off your vacuum cleaner.
For automatic mode vacuuming
(working with power tools):
8. Adapt the power tool adapter (25) to the dust
extraction outlet of the power tool. Using a knife
if necessary.
9. Connect the power tool adapter (25) to the han-
dle adapter (18) and connect it to the power tool
dust extraction outlet.
10. Connect the mains plug of the power tool to the
power socket (15).
11. Connect the mains plug.
12. Press the power switch (1) into the " Automatic
mode / II" position and start working to start your
vacuum cleaner. The vacuum cleaner is automat-
ically switched on/off via the power tool. As soon
as the power tool is switched on, the vacuum
cleaner starts with some delay. If the power tool
is switched off, the vacuum cleaner continues to
run for some seconds in order to vacuum up the
remaining dirt in the suction hose (17).
13. Press the power switch (1) into the " OFF/0" posi-
tion to switch off your vacuum cleaner.
Wet vacuuming (Fig. A, C, E – F, H)
The vacuum cleaner is equipped with a float
(30). The suction power decreases when
the maximum filling level is reached. Switch
the vacuum cleaner off (1) immediately.
Remove the plug from the socket and
empty the container (8).
Clean the float (30) at regular intervals, and
check it for damage. Otherwise, its function
can be impaired.
Never reach into the water to be suctioned
up. Danger of electric shock.
Immediately switch (1) the machine off if
foam forms or liquids escape!
Do not use a dust collection bag (26)!
1. Press the power switch (1) into the " OFF/0" posi-
tion and remove the mains plug from the mains.
2. Unlock the locking clamp (7) and remove the
top section (6).
3. Before wet vacuuming, remove the dust collec-
WWW.VONROC.COM
tion bag (26), the HEPA filter (27) and remove all
dirt and debris from the container (8).
4. Carefully slide foam filter (28) down over the filter
cage (31) making sure the whole cage (31) is
covered as shown in Fig. C-2.
5. Reattach the top section (6) again and lock the
locking clamp (7).
6. Insert one end of the hose (17) into the vacuum-
ing port (14). Fully unwind the suction hose (17).
7. Connect the mains plug.
8. Press the power switch (1) into the " ON/I" posi-
tion to start your vacuum cleaner.
9. The machine now is ready for wet vacuum
cleaning.
10. Press the power switch (1) into the " OFF/0" posi-
tion to switch off your vacuum cleaner.
11. Raise the hose (17) so that the liquids drains into
the container (8).
12. Empty the container (8) immediately after suction
cleaning because it is not designed to store
liquids.
Blow function (Fig. A, E – F)
Operation without the use of a filter is
recommended.
Remove all dirt and debris from the
container (8) before you use the blow
function.
Always wear safety goggles before using
the blowing function.
Risk of flying objects. Keep bystanders
away from the work area.
Your vacuum cleaner is equipped with a blowing
function. It can be used to blow dust and debris.
1. Press the power switch (1) into the " OFF/0" posi-
tion and remove the mains plug from the mains.
2. Unlock the locking clamp (7) and remove the top
section (6).
3. Before blowing, remove the dust collection bag
(26), the filter (27, 28) and remove all dirt and
debris from the container (8).
4. Reattach the top section (6) again and lock the
locking clamp (7).
5. Insert one end of the hose (17) into the blowing
port (3) on top of machine. Fully unwind the
suction hose (17).
EN
9