Descriptions Of Main Functions - Chasing F1 Bedienungsanleitung

c. Connect Sonar Bracket/ Bait Boat to Fish Detector：
Connect the Bait boat to the Fish Detector. Make
sure the hanging bucket and cable are in place.
Note： 1) Before installing or disassembling the
Bait Boat, turn off the Fish Detector' s power.
Start the Fish Detector
3
To start the Fish Detector, press the power button.
The power indicator lights up, and the navigation
light exhibits a short flash, accompanied by two
beeps sounds of self-test.
Registration & Login
5
When you launch the CHASING GO2 App for the
first time, please follow the interface prompts to
register an account and log in to the App. A network
connection is required during the registration and
login process.
Hide/Show Device
camera probe connection status
orientation
One-key
return
Camera probe
orientation indication
Menu
Lock/
Unlock
Bait boat
switch
05
Connect the Sonar bracket to the Fish Detector.
Clip the sonar hanging buckle to the Fish Detector
and move it slightly to make sure it is attached and
mounted properly.
Wi-Fi Connection
4
On the smartphone/tablet, go to Wi-Fi settings. Wait
for 5-10 seconds and the Chasing_xxxx network will
appear as an option. Hit to connect and enter the
Wi-Fi password: 12345678
6:27 89%
Wi-Fi
Settings
Wi-Fi
Chasing_xxxxx
CHOOSE A NETWORK...
Gladius_5G_xxxxx
xxxxxxxxxx
xxxxxxxxxx
CHASING GO2 App Tutorial
6
xxxxxxxxxx
Run the App, when you see "connected" on the
bottom left corner, hit "start" on the right. Now you
will see the main App interface (below).
Current Depth Temperature GPS Battery
mode

Descriptions of Main Functions

1
Navigation light: It is convenient to observe the position of the Fish Detector at night, and it also has the
effect of attracting fish. In normal mode, it is located in the menu bar.
2
IR Infrared Light: Turn it on in the low light conditions or dark underwater environment for better vision.
In normal mode, it is located in the menu bar.
3
Picture and video： Photos can be taken while recording.
4 Ascend and Descend:
· Manual
This function is only enabled in professional mode. The speed of the probe releasing and retracting can
be controlled by adjusting the slider, more closer to the end of sides, more faster.
Ascend： Slide up and press long, release to stop.
Descend: Slide down and press long, release to stop.
· Auto
Ascend: Hit the probe retracting slider, hit again to stop
Descend: Hit the probe releasing slider, hit again to stop
Lock/Unlock:
5
Hit the Lock/Unlock button to unlock the thruster and use the virtual joy stick on screen to control the
Fish Detector' s movement.
Forward
Left
Backward
Fishing point and return:
6
1) Setting the return point: After unlocking, a pop-up will appear on the interface to prompt setting the
return point. Hit "Confirm setting" and then set the Fish Detector 's current. osition as return point. If
you hit "Ignore", you can set the return point when the Fish Detector moves to the position where
Settings
you want to return.
2) One-key return： If the return point has been set, hit the "one-key return button" again, Slide to the
right to perform the one-key return function, and slide to the left to "reset the return point".
Wind-up
3） Add fishing point：
button
Hit the "Fishing point Function" button. You can add fishing point here and change the name and
Record add notes according to your personal needs.
video
4） Fishing points list： Hit to view the saved fishing points.
5） Go to the selected fishing point： Hit "Go Here" in the list of fishing points and the Fish Detector will
Wind-down
button
head to the selected fishing point
IR Infrared
Note: The fishing point function is located inthe menu bar.
Light switch
Right Pan Left Pan Right
06