Slope Operation In The Horizontal Position; Slope Memory For Slope Operation In Horizontal Position (Grl 650 Chvg); Slopeprotect; Manual Operation - Bosch GRL 600 CHV Anwenderhandbuch- Originalbetriebsanleitung

Now check the position of the laser beam at a reference
point and, if necessary, correct the height or alignment of
the measuring tool.
To adjust/switch off the shock-warning function:
On the start screen, the current setting is shown with the
shock-warning indicator (c):
Shock-warning function is switched on at high
sensitivity.
GRL 650 CHVG: Shock-warning function is
switched on at reduced sensitivity.
Shock-warning function is switched off.
Briefly press the on/off button (11) to adjust
the shock-warning function setting. Then press
the on/off button (11) in the menu which sub-
sequently appears as many times as needed
(GRL 600 CHV)
until the required setting has been selected.
Confirm your selection with
slope button (14).
(GRL 650 CHVG)
If the shock-warning function has been switched on, it will be
activated after approximately 30 seconds.

Slope operation in the horizontal position

In the measuring tool's horizontal position, the X-axis and the
Y-axis can be tilted independently of each other in a range of
±8.5%.
To tilt the X-axis, press the slope
button (14) on the measuring tool or
the slope button (31) on the remote
control once. The menu for setting the
slope of the X-axis will appear.
Set the required slope by using the buttons ▲ (4) or ▼ (3)
on the measuring tool or using the up (30) or down (35)
slope buttons on the remote control. Pressing both slope
buttons on the measuring tool or on the remote control at
the same time resets the slope back to 0.00%.
To tilt the Y‑axis, press the slope
button (14) on the measuring tool or
the slope button (31) on the remote
control again. The menu for setting the
slope of the Y-axis will appear.
Set the required slope in the same way as outlined for the
X‑axis.
The selected slope is implemented on
the measuring tool a few seconds after
the last press of a button. Both the
laser beam and the symbol for setting
the slope on the display will flash until
the process of setting the slope has
been completed.
Bosch Power Tools
continuously.
Slope memory for slope operation in horizontal position
(GRL 650 CHVG)
The measuring tool saves the four most recently used slope
values of both axes. As an alternative when readjusting the
slopes, you can apply these saved slope combinations.
Start the slope operation for the X‑axis (see "Slope operation
in the horizontal position", page 45).
by pressing the
Confirm the selection by pressing the slope button (14) on
the measuring tool ( ) or the slope button (31) on the re-
mote control. The slope combination is implemented on the
measuring tool a few seconds after the button is pressed
(see "Slope operation in the horizontal position", page 45).
To set a value other than one of those saved, press the ▲
button (4) on the measuring tool (
button (30) on the remote control. The indicator returns to
the slope operation settings menu (see "Slope operation in
the horizontal position", page 45).

SlopeProtect

Temperature changes in the measuring tool can have effects
on the set slope of the axes.
To avoid measurement inaccuracies, the slope of the axes is
readjusted when exceeding the set temperature difference.
The measuring tool is levelled in, then it returns to slope op-
eration with the previously set values.
The slope is reset at temperature changes of ≥5 °C.
GRL 650 CHVG: Using the Bosch Levelling Remote App,
the temperature difference can be lowered to 2 °C or the
SlopeProtect function can be switched off altogether. This
setting is not saved when the measuring tool is switched off.

Manual operation

The automatic levelling of the measuring tool can be
switched off (manual operation):
English | 45
After the process of setting the slope
has been completed, the set slope val-
ues of both axes will be shown on the
start screen. The status indicator (12)
on the measuring tool will light up red
continuously. On the remote control,
the status indicator for the tilted axis
((34) and/or (33)) will light up red
To call up the slope memory, press the
line operation button (5) on the meas-
uring tool or the line operation
button (28) on the remote control.
To select one of the four saved com-
binations, press the line operation
button (5) on the measuring tool or
the line operation button (28) on the
remote control as many times as
needed until the required combination
is indicated on the display.
) or the slope up
1 609 92A 6AE | (28.05.2021)