Electrical Safety; Handling Safety; Installation Safety - Beko GN163240ZXBRN Bedienungsanleitung

Safety instructions
A

1.3 Electrical safety

The product shall not be plugged into the outlet
during installation, maintenance, cleaning, re-
pair, and transportation operations.
If the power the cord is damaged, it shall be
replaced by authorized service only to avoid
any risk that may occur.
Do not tuck the power cord under the product
or to the rear of the product. Do not put heavy
items on the power cord. The power cord
should not be bent, crushed, and come into
contact with any heat source.
Do not use an extension cord, multi-plug or
adaptor to operate your product.
Portable multi sockets or portable power sup-
plies may overheat and cause fire. Thus, do not
have a multi-plug behind or in the vicinity of
the product.
The plug shall be easily accessible. If this is
not possible, a mechanism that meets the
electrical legislation and that disconnects all
terminals from the mains (fuse, switch, main
switch, etc.) shall be available on the electrical
installation.
Do not touch the plug with wet hands.
When unplugging the appliance, don't hold the
power cord, but the plug.
A

1.4 Handling Safety

This product is heavy, do not handle it by your-
self.
Do not hold the product from its door while
handling the product.
Be careful not to damage the cooling system
and the pipes while handling the product. Do
not operate the product if the pipes are dam-
aged, and contact an authorized service.
A

1.5 Installation Safety

Contact the Authorized Service for the prod-
uct's installation. To prepare the product for in-
stallation, see the information in the user guide
and make sure the electric and water utilities
are as required. If the installation is not suit-
able, call a qualified electrician and plumber to
have them make the necessary arrangements.
Otherwise, electric shock, fire, issues with the
product or injuries may occur.
Check for any damage on the product before
installing it. Do not have the product installed if
it is damaged.
Place the product on a level and hard sur-
face and balance with the adjustable legs.
Otherwise, the refrigerator may tip over and
cause injuries.
The product shall be installed in a dry and ven-
tilated environment. Do not keep carpets, rugs
or similar floor covers under the product. This
may cause risk of fire as a result of inadequate
ventilation!
Do not block or cover ventilation holes.
Otherwise, power consumption may be in-
creased and damage to your product may
occur.
Do not connect the product to supply systems
such as solar power supplies. Otherwise, dam-
age to your product may occur as a result of
the abrupt voltage fluctuations!
The more refrigerant a refrigerator contains,
the bigger its installation room shall be. In
very small rooms, a flammable gas-air mixture
may occur in case of a gas leak in the cooling
system. At least 1 m³ of volume is required for
each 8 grams of refrigerant. The amount of the
refrigerant available in your product is specified
in the Type Label.
The installation place of the product shall not
be exposed to direct sunlight and it shall not be
in the vicinity of a heat source such as stoves,
radiators, etc.
If you cannot prevent installation of the product in
the vicinity of a heat source, you shall use a suit-
able insulation plate and the minimum distance to
the heat source shall be as specified below.
- At least 30 cm away from heat sources such
as stoves, heating units and heaters, etc.,
- And at least 5 cm away from electric ovens.
Your product has the protection class of I. Plug
the product in a grounded socket that con-
forms with the Voltage, Current and Frequency
values specified in the type label. The socket
outlet shall be equipped with a fuse with a
rating of 10 A – 16 A. Our company shall not
be responsible for the damages that shall be
incurred as a result of operating the product
without ensuring ground and electrical connec-
4 /29 EN
Refrigerator / User Guide