Technical Data; Unpacking - Redstone MT100 Original Bedienungsanleitung

Residual risks
The machine has been built according to the state of
the art and the recognised technical safety require-
ments. However, individual residual risks can arise
during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed
along with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your machine provides optimal perfor-
mance.
• Hands may never enter the processing zone when
the machine is in operation.
• Release the handle button and switch off the ma-
chine prior to any operations.
WARNING! This electric tool generates an elec-
tromagnetic field during operation. This field can
impair active or passive medical implants under
certain conditions. In order to prevent the risk of
serious or deadly injuries, we recommend that
persons with medical implants consult with their
physician and the manufacturer of the medical
implant prior to operating the electric tool.

7. Technical data

AC motor
Power
Idle speed n
0
Cutting wheel
Spindle thread
Base
Swivel range
Max. vice clamping width
Cutting width at 90° max*
Weight ca.
Subject to technical changes!
* max. possible passage height. In order to work safe-
ly, the workpiece height must not exceed 110 mm.
34 | GB
LEROY MERLIN • Rue Chanzy - Lezennes 59712 Lille Cedex 9 - FRANCE
230-240 V~ 50Hz
2300 Watt
3500 min
-1
ø 355 x 25,4 x 3,2 mm
M10
560 x 310 mm
0 - 45°
200 mm
Ø 115 / 140 x 80 mm
17,9 kg
Noise & Vibration
Total noise values determined in accordance with EN
62841.
Noise emission values
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
The overall vibration values (vector sum of three di-
rections) have been determined according to EN
62841.
Warning:
The noise emissions during the actual use of the pow-
er tool may differ from the above-mentioned values
depending on the power tool being used, in particular
on the type of workpiece being processed.
Try to keep emissions as low as possible, for example
by limiting your working time.
In this regard, all the operational cycle phases must
be taken into consideration (such as the times when
the tool is switched off or running idle).
Vibration parameters
Vibration emission value a
h
Uncertainty K
The specified vibration emission value has been
measured according to a standardised testing proce-
dure and can be used for comparison of one electric
tool with another;
The specified vibration emission value can also be
used for an initial assessment of the load.
Warning:
The vibration emission value can vary from the spec-
ified value during the actual use of the electrical tool,
depending on the type and the manner in which the
electrical tool is used; try to keep stress from vibra-
tions as low as possible. Some examples of means
for reducing the vibration stress are wearing gloves
while using the tool and limiting work time. In doing
so, all parts of the operating cycle must be taken into
account (such as times in which the electric tool is
switched off or times in which it is switched on, but is
not running under a load).

8. Unpacking

• Open the packaging and remove the device care
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
95 dB(A)
3 dB
108 dB(A)
3 dB
4,2 m/s²
1,5 m/s²