Conrad 99 43 99 Bedienungsanleitung Seite 2

O P E R A T I N G I N S T R U C T I O N S
USB3.0 Gigabit network adaptor
Item no. 99 43 99
Intended use
The product is designed to be connected to the USB port on a computer and it is intended to
serve as a network port (10/100/1000MBit).
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package Contents
• Gigabit network adaptor
• CD with driver (and manufacturer's operating instructions in English language)
• Quick guide
Features
• USB3.0
• 10/100/1000MBit network port, RJ45 port
Driver Installation, Connection
☞
Do not connect the USB gigabit network adaptor to the computer yet. First of all,
install the necessary driver from the CD provided.
Insert the enclosed CD into an appropriate drive on your computer.
If the installation program does not start automatically, start the program "Autorun.exe". Click
on the "Driver" button next to the line "USB3.0 TO Gigabit Ethernet". Afterwards, a directory
with the drivers matching the gigabit network adaptor opens.
Open the directory "PC driver" for the installation under Windows and start the application
"Setup.exe" contained in this directory.
☞
Depending on the Windows version, administrator rights might be necessary to in-
stall the drivers.
After completion of the driver installation connect the gigabit network adaptor to a USB3.0 port
of the computer. Connect the RJ45 port of the gigabit network adaptor to your switch or router
using a 1:1 connected network cable.
It might be necessary to restart Windows, before the gigabit network adaptor can work cor-
rectly.
Tips and Notes
• The gigabit network adaptor should only be connected to a USB3.0 port of the computer be-
cause a USB1.1-/USB2.0 port is not only too slow but it also does not provide enough current
for the operation of the gigabit network adaptor (USB3.0 provides up to 900 mA, USB1.1/2.0
only 500 mA).
• If you have a network or system administrator who is responsible for your network (for exam-
ple in a larger company), allow him or her carry out the connection and driver installation; do
not install the gigabit network adaptor yourself.
• The stated maximum data transfer rate of 10/100/1000MBit will not be attained in practice.
This is due to the communication method used, transmission errors, other devices in the
network etc.
• With Windows, it might take some time until the PCs appear on the network.
Normally, you cannot access another PC immediately after you have switched on the PCs and
Windows is loaded on all PCs.
If, after a few minutes, it is still not possible to access other PCs, check any fi rewall and/or
virus scanner settings that may be used.
Naturally, the access permissions also have to be set accordingly, if you are using an operat-
ing system that offers such features.
Consult the applicable operating instructions, when using a network printer or other devices
in the network.
There are numerous causes explaining why a network connection is not successful. Please
refer to the appropriate specialist literature or to a specialist technician.
• If you are not using a DHCP Server (e.g. integrated in all DSL-routers), you should assign a
static IP address to each device within the network.
For example, set the router to 192.168.1.1, set the fi rst computer to 192.168.1.2, the second
computer to 192.168.1.3, and so on.
The fi rst three digits must be the same on all computers; the last digit can range from 1 to
www.conrad.com
254.
The "subnet mask" has to be set to 255.255.255.0 for all the computers in the network.
Version 01/13
Please keep in mind that an IP address (such as 192.168.1.1) can only be used once in the
network. When you set your router to the IP address 192.168.1.1, no other device in the
network can use this IP address!
• Always ensure suffi cient ventilation of the gigabit network adapter. It may heat up consider-
ably during operation. Do not cover the gigabit network adapter.
• The CD includes the operating instructions of the manufacturer (in PDF format). To view
the fi le, you need e.g. the Acrobat Reader, which you can download free of charge at www.
adobe.com.
• There are two LEDs on the gigabit network adaptor, which indicate the corresponding func-
tion:
LED " Link"
LED "Duplex"
Disposal
LED does not light LED fl ashes slowly
No connection The connection is
being established
No connection The connection is
being established
Dispose of an unserviceable product in accordance with the relevant statutory regu-
lations.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2013 by Conrad Electronic SE.
LED fl ashes fast
Connection is active
Connection active,
duplex transfer