KikkaBoo FELIX Gebrauchsanweisung Seite 12

3.3.Then insert the lap and diagonal belt onto the vehicle seat belt buckle .You will hear a click when it's correctly inserted. Pull on it to check
it is securely tted.
IV. INSTALLATION OF CHILD SEATS (GROUP I: 9-18KG)
This product is suitable for children with weight in 9-18kg.
Installation method 1 REARWARD FACING INSTALLATION:
Step 1: First adjust the seat to the most inclined gear, and then rotate the seat body 180 degrees on the car seat.
Step 2: Secure the seat to the car seat with ISOFIX, make sure the ISOFIX is locked, the display window appears green,and then slowly push
the seat onto the back of the car seat until it ts completely.
Step 3: Loosen the buckle and shoulder strap, put the child in the child's seat, and then buckle and pull the shoulder strap.
Check the shoulder strap and head height. Note: all seat belts should not be twisted.
Step 4: Use the adjusting buckle on the top sling to adjust the top sling to the appropriate length. The top sling of the seat is passed through
the side of the head of the seat. The top sling is attached to the corresponding hook on the car (the node suggested in the
manufacturer's manual). Finally tighten the top sling. when the top sling is secured, its regulator is shown as green.
Installation method 2 FORWARD FACING INSTALLATION:
Step 1: Use ISOFIX to secure the seat to the car seat, make sure the ISOFIX is locked, the display window appears green, and then push the
seat slowly to the back of the car seat until fully tted.
Step 2: Pull out the top sling. Use the adjustment buckle on the top sling to adjust the top sling to the appropriate length. Hang the top sling
on the corresponding hook of the car (the node recommended in the carmaker's manual). Finally, the top sling is
tightened, and when the top sling is xed, the regulator shows green.
Step 3: First loosen the pull-out buckle and
shoulder strap, put the child into the child seat, and then buckle the pull-out buckle to tighten the shoulder strap. Refer to 4.2 and 4.3 to
check shoulder strap and head height. Note: All seat belts must not be distorted. Its regulator shows green.
V. INSTALLATION OF CHILD SEATS (GROUP II,III: 15-36KG)
This product is suitable for children weighing 15-36 kg. Forward installation (remove seat belt and buckle).
Installation method 1:
Step 1: First adjust the child seat to the most upright le, and then put it on your car seat.
Step 2: Place the child on the child's safety seat and secure the child with a three-point safety belt for the vehicle. Note: All safety belts shall
not be twisted.
Installation method 2:
Step 1: First adjust the child seat to the most upright le, and then put it on your car seat.
Step 2: Second, use FIX to secure the child safety seat to the car seat, and then use the car three-point safety to bring the child xed. Note: all
seat belts should not be twisted.
VI. REMOVAL OF SEAT BELTS AND BUCKLES
Step 1: Remove the straps of the straps as shown in gure 6.1,6.2,6.3,6.4.
Step 2: As shown in gure 6.5,6.6,6.7 to loosen the buckle and remove the sleeping pad and crotch pad, with shoulder straps stacked under
the sleeve. Remove the sun-shaped iron from the base of the seat and remove it from the buckle.
VII. MAINTENANCE AND CLEANING
THE ROUTINE MAINTENANCE
• During daily use, children's seat wear and tear need to be checked. In the event of an accident, the seat needs to be replaced.
• When not using child safety seats, place them in a dry, ventilated place to avoid damp and moldy seats.
• If dust is found on the surface of the child's seat, dry the seat belt and plastic parts with a damp sponge and then dry by ventilation.
• If you drop food or drink onto your seat belt, remove it and rinse it with warm water, then dry by ventilation.
• If you want to clean the entire seat cover, please refer to the 6.2 washing instructions.
THE WASH CARE INSTRUCTION
Solvents, chemical cleaners and lubricants are prohibited for any part of this product.
Hand washable, water temperature is less than 30 degrees. No drying, No ironing,Unbleached
THE REMOVAL AND DRESSING OF THE FABRIC COVER
1. Remove shoulder straps and shoulder covers;
2. Release the buckle rst, then remove the crotch pad and sleeping pad. ( gure 7.1)
3. Unbutton the headrest and base, respectively, and remove the sleeve. ( gure 7.2)
Note: if you need to install the cover again, please operate in reverse order of removal.
ENGLISH