Herunterladen Diese Seite drucken

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

DE
GB
a
Schutzwinkel
Montageanleitung
Fangstange
Blitzschutz
a
Schutzwinkel
a
Schutzwinkel
Blitzschutz

Werbung

loading

Inhaltszusammenfassung für Dehn 105 425

  • Seite 1 Schutzwinkel Montageanleitung Fangstange Blitzschutz Schutzwinkel Schutzwinkel Blitzschutz...
  • Seite 2 1. Anwendung "Getrennten Blitz­ schutz Fangeinrichtungen" Schutz- Schutz- "Schutzwinkelverfahren" winkel winkel Schutz- winkel h (m) Tabelle 1 Berechnung der Fangstange Fig. 1 Schutzwinkel a nach Tabelle 1...
  • Seite 3 Fangstangen mit Betonsockel 2.1 Montage 2.1.1 Betonsockel Anmerkung: Fangstangen- Fangstange Fangstange Betonsockel Unterteil / komplett Æ 16 / 10 mm je Strebe Alu-Rohr Æ 22 x 4 mm Tabelle 2 Fangstangen von 2500 bis 3500 mm...
  • Seite 4 Fig. 2 Betonsockel...
  • Seite 5 2.2 Fangstange Æ Æ 2.2.1 Ableitung...
  • Seite 6 Æ Æ Fig. 2.2 Strebengestell / Betonsockel / Fangstange...
  • Seite 7 Anpassung der Fangstange bei Dachneigungen bis zu einem Neigungswinkel von 10° 2.3.1 Adaptereinstellung Æ Fangstangen-Unterteil Æ Anzugsdrehmoment M 10 Fig. 2.3 Adaptereinstellung...
  • Seite 8: Montage

    Fangstangen für Metalldächer 3.1 Montage Æ 3.1.1 Dachleitungshalter 3.1.2 Anpassung des Strebengestells Anmerkung: Fangstangen- Fangstange Fangstange Leitungshalter / Unterteil / komplett Æ 16 / 10 mm Klemmen Alu-Rohr Æ 22 x 4 mm Tabelle 3 Fangstangen von 2500 bis 3500 mm...
  • Seite 9 M8 / 15 Nm Æ Strebengestell M8 / 15 Nm) Dachprofil, Dachprofil, Dachprofil, Dachprofil, Rundstehfalz Stehfalz Rundstehfalz Stehfalz 2x Sechskantmutter M8 / Anzugsdrehmoment 15 Nm Detail Detail -Darstellung -Darstellung Fig. 3 Strebengestell...
  • Seite 10 3.2 Fangstange Æ Æ 15 Nm 3.2.1 Ableitung des Blitzstrom...
  • Seite 11 Æ Æ Dachprofil Dachprofil yp: Rundstehfalz yp: Rundstehfalz Fig. 3.2 Strebengestell / Fangstange...
  • Seite 12 Anpassung der Fangstange bei Dachneigungen bis zu einem Neigungswinkel von 10° 3.3.1 Adaptereinstellung Fangstangen-Unterteil Anzugsdrehmoment Fig. 3.3 Anpassung Fangstange...
  • Seite 13: Lightning Protection

    protective angle Installation Instructions Air-Termination Rod Lightning Protection protective angle protective angle Lightning Protection...
  • Seite 14 1.Use ”isolated air-terminations” ”protective angle me­ protective protective thod” angle angle protective angle h (m) Table 1 Calculation of the air-termination rod Fig. 1 Protective angle according to table 1...
  • Seite 15: Installation

    Air-termination rods with concrete block 2.1 Installation 2.1.1 Concrete block Note: Air-termination- Lower part of the Complete air- air-termination Concrete block rod with a termination-rod rod / aluminium tube per brace diameter of Æ 22 x 4 mm Æ 16 / 10 mm Table 2 Air-termination rods from 2500 bis 3500 mm...
  • Seite 16 Fig. 2 concrete block...
  • Seite 17 2.2 Air-termination rod Æ 2.2.1 Down conductor...
  • Seite 18 Æ Æ Fig. 2.2 Brace frame / concrete block / air-termination rod...
  • Seite 19 2.3. Adjustment of the air-termination rod in case of roof inclinations up to an inclination angle of 10° 2.3.1 Adjustment of the adapter Æ lower part of the air-termination rod Æ tightening torque Fig. 2.3 Adjustment of the adapter...
  • Seite 20 Air-termination rods for metal roofs 3.1 Installation 3.1.1 Roof conductor holders 3.1.2 Adjustment of the brace frame Note: Lower part of the Complete air- Air-termination- air-termination rod / Conductor holders / termination-rod rod with a diameter aluminium tube clamps of 16 / 10 mm Æ...
  • Seite 21 / 15 Nm Æ brace frame / 15 Nm) Roof profile, Roof profile, Roof profile, Roof profile, type: round type: standing type: round type: standing standing seam seam standing seam seam 2 M8 hexagon nuts / tightening torque of 15 Nm Detailed Detailed view...
  • Seite 22 3.2 Air-termination rod Æ 15 Nm 3.2.1 Discharge of lightning current...
  • Seite 23 Æ Æ Roof profile Roof profile type: round type: round standing seam standing seam Fig. 3.2 Brace frame / air-termination rod...
  • Seite 24 Adjustment of the air-termination rod in case of roof inclinations up to an inclination angle of 10° 3.3.1 Adjustment of the adapter lower part of the air-termination rod tightening torque for the M8 locking bolt Fig. 3.3 Adjustment of the air-termination rod...

Diese Anleitung auch für:

105 430105 435103 221103 231105 405105 410