Care And Cleaning - KIKKA BOO ALLURE Gebrauchsanweisung

PARKING BRAKE ( g.28, g.29)
Engaging the brake: Press the brake lever as shown in the gure and push the stroller slightly forwards to ensure that the brake is engaged
correctly. Disengaging the brake: Press the brake lever as shown in the gure to disengage the brake.
FITTING THE STROLLER RAIN COVER ( g.30) Fit the rain cover on the canopy and secure it to the frame.
CHANGING THE SEAT IN THE PRAM VERSION (da g.31 a g.36)
ATTENTION: The product in the pram version is suitable for a baby that is unable to sit up and turn over alone and pull him/herself up on
his/her hands and knees. Maximum weight of the child 9 kg.
Release buckle " " and "B" located under the seat ( g. 32). Recline the backrest, pressing the button in the middle of adjustment device
"D" and sliding it downward (see how to recline the backrest in the "STROLLER VERSION SEAT" section.
Adjust the seat chassis horizontally, see the "ADJUSTING THE SEAT" section ( g.31). Adjust the footrest horizontally, see the "ADJUSTING THE
FOOTREST " section ( g.31 A).
WARNING:The pram must only be used in the horizontal position ( g. 34). Never incline the pram.
For babies from birth to about 6 months of age, the stroller must be used in pram con guration. When the seat is in pram con guration, it
must be fastened to the stroller facing the parent ( g.31). DO NOT remove the pram from the stroller with the baby inside.The seat, even in
the carrycot version, must always ONLY be used tted on the chassis. he bumper bar must never be used as a handle to lift the product
with the child inside ( g.35). Do not use the canopy to lift the product with the child inside ( g.36).
FOLDING THE STROLLER (from g.37 to g.43)
Before folding the stroller, ensure that:
• The backrest is adjusted to the vertical position.
• The canopy is closed back up.
• The front wheels are in swivel mode.
Push the stroller forwards to direct the front wheels longitudinally. Move button "A" to the right, as shown in the gure, while pressing
button "B" at the same time. Fold the handlebar downwards. Bring the front wheel chassis towards the back. Fold up the footrest.
Make sure it is closed properly.
OPENING THE STROLLER (from g.43 to g.48)
Place the stroller as shown in the gure. Lift closing lever "A'' (right side), as shown in the gure ( g.44), while lifting the handlebar
upwards until the stroller opens completely. Before using the stroller, make sure it is opened properly and the mechanisms are properly
locked ( g.48).
IF YOU WISH, YOU CAN USE THE ALLURE CAR SEAT (GROUP O+) WITH THE STROLLER CLOSELY FOLLOW THE INSTRUCTIONS BELOW.
Remove the seat from the chassis, see the "Fitting the seat" paragraph.
USING THE CAR SEAT ACCESSORY ( g.49)
IMPORTANT: the car seat accessory must only be tted to the chassis facing the parent.
Engage the stroller parking brake. Remove the stroller seat. Fitting the adapters (from g. 50 to g.53). Insert the adapters on the car seat
side, see g.51, g.52, g.53. Make sure the adapters are properly inserted and fastened to the car seat.
Removing the adapters ( g.54, g.55) To remove the adapters, press the red "A" button on the upper part of the car seat while removing
the adapter from it. Fastening the car seat to the stroller chassis ( g. 56).Position the car seat with the adapters inserted facing the parent
and, after having lined up the fastening systems, press downward until you hear a click, indicating proper fastening.
IMPORTANT: Make sure both sides are fastened correctly; the car seat must not detach from the stroller chassis if lifted upwards.
Releasing the car seat from the stroller chassis ( g. 56 - g. 57) Put the car seat handle in the upright position, pressing the red buttons on
the side. See the manual supplied with the car seat. Hold the car seat handle with one hand and, with the other, alternatively lift levers "A"
and removethe car seat, lifting it by the handle.

CARE AND CLEANING

Fabric parts:
The fabrics of the product must be cleaned with warm water and mild soap.
Plastic and metal parts:
1. The plastic and metal parts must be cleaned with a damp soft cloth and dried with dry soft cloth.
2. Do not let the product exposed to the harmful e ect of external factors - direct sunlight, rain, snow or wind. This may lead to damage
of the metal and plastic parts and fading of the fabrics of the crib.
3. When you are not using the product, store it at a dry and well ventilated place, not in dusty, humid premises with very high or very low
room temperatures.
Frame: From time to time check all plastic parts that are hanged on the frame. Tighten all screw and bolts if necessary.
ENGLISH