Interlogix RK100N-S60 Montageanleitung Seite 3

Switching points
Details can be found at Figure 6.
It is possible to adjust the switch point of the bolt contact with a
locking disk on to the designated switch point.
Set the switch point 1 until 4 with the tip of a screwdriver. Raise
the locking disk on the notch and turn until it engages again.
Schematic diagram
Colours:
(CO) Combined - white
(NC) Single pole NC contact - green
(NO) Single pole NO contact - brown
Technical data
Item No. RK100N-S60
Cable LIYY 3 × 0,14mm²
Contact termination
Protection category IP67/DIN 40050
VdS Class C
VdS No G110103
Designated use For mounting on internal and external doors
Contact capacity max. 3 W / VA
Switch voltage max. 30 VDC
Switch current min. 5 mA
Switch current max. 300 mA
Contact type Change over
−25°C to +70°C
Temperature at fixed
cable
−5°C to +50°C
Temperature at
moveable cable
Switch point Adjustable
Cycles of operation min. 30,000
Regulatory information
Manufacturer
PLACED ON THE MARKET BY:
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092,
USA
AUTHORIZED EU REPRESENTATIVE:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Certification
P/N 75009040.Yxx • REV B • ISS 21MAR19
Product warnings THESE PRODUCTS ARE INTENDED FOR
and disclaimers SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
European Union UTC Fire & Security hereby declares that this
directives device is in compliance with the applicable
requirements and provisions of the Directive
2014/30/EU and/or 2014/35/EU. For more
information see www.utcfireandsecurity.com or
www.interlogix.com.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info
Contact information
For more information visit our website: www.interlogix.com.
DE: Montageanleitung
Montageort
Der Riegelschaltkontakt ist zur Montage u.a. im
Türschließblech zur Verschlussüberwachung der Verriegelung
geeignet. Die Betätigung des Riegelschaltkontaktes erfolgt
durch den Schloßriegel. Die Meldung kann für
Einbruchmeldeanlagen und Überwachungssysteme
ausgewertet bzw. angezeigt werden.
Lieferumfang (siehe Abbildung 2)
1. Riegelschaltkontakt
Hebelverlängerung (Kunststoff)
2.
Hebelverlängerung (Metall)
3.
4. Kunststoffhalter
5. Blechschraube 2,2 x 4,5
6. Senkkopfschraube M3 x 6
7. Montageanleitung
Abmessungen
Siehe Abbildung 3.
Für die Zugentlastung wird eine Leitungsschlaufe mit dem
Kunststoffhalter gelegt.
or scan the QR code.
3 / 4