Maintenance And Care - Vitek VT-2167 W Betriebsanweisung

Notes: Every pressing of the buttons (10)-(13) is
accompanied with a sound signal.
«TIMER» button
•
To set the operation time of the heater press
the button (10) «TIMER» in the standby mode,
the operation time 1 and the indicator
appear on the display (3). Press the buttons
(12) «+»/«–» to set the required operation time
of the heater in the range from 1 to 24 hours.
If no buttons are pressed within 3 seconds, the
unit will save the last operation time value. At
the end of the set time the unit will be switched
off automatically.
Safety lock
• This unit is equipped with the «Child safety
lock». Press and hold down the buttons «+»
and «–» simultaneously for 3 seconds, the dis-
play will show the symbol
safety lock function off, press again and hold
down the buttons «+» and «–» simultaneously
for 3 seconds.
«MODE» button
• When you press the button (11) «MODE»,
the heater is switched to economy operation
mode, the symbol appears on the display (3)
and the unit operates in the low power mode.
In this mode the unit starts heating only if the
temperature is bellow +29°C. When you press
the button (11) «MODE» again, the heater will
switch to freeze preventing mode, the symbol
appears on the display (3). In this mode the
unit starts heating in high power mode only if
the temperature is bellow +3°C; after the room
temperature reaches the value from +3°C to
+5°C, the unit will be switched to the low power
mode. Press the button (11) «MODE» again,
and the heater will be switched back to auto-
matic keep warm mode. In this mode the unit
starts heating the room when the room tem-
perature is 1°С below the preset temperature,
and stops heating when the room temperature
is 1°С above the preset.
• To switch the unit off, set the switch (1) to the
position «OFF», then unplug the unit.
Notes:
While the first switching on the heating element
–
burns, therefore occurrence of a small amount
of smoke or foreign smell is possible. It is normal.
VT-2167.indd 5
Do not open windows and doors when the unit
–
is operating; otherwise you will not get the
desired results, due to cold air inflow.
AUTO SWITCH-OFF FUNCTION
The unit is equipped with auto switch-off function
will in case of overheating or if it is dropped.
• In case of the unit overheating, the automatic
thermal switch will go off, and the heater will
be switched off.
•
In this case immediately remove the power
plug from the mains socket.
•
Make sure that the grids are not blocked and
nothing prevents air flow.
•
Let the heater cool down for approximately
10-15 minutes before switching it on again.
• Connect the unit to the mains and switch it on.
• If the unit cannot be switched on, it may
mean that the heater is damaged. In this
. To switch the case contact the authorized service center
for repair.
•
The unit is also equipped with an automatic
switch that switches the unit off when it is
dropped or considerably tilted. When the unit
is returned to the vertical position, there will be
a sound signal and the unit will be switched on
with the previous settings saved. If this does
not occur, contact the authorized service cen-
ter to repair the unit.

MAINTENANCE AND CARE

•
Before cleaning the heater, switch it off and
unplug it.
•
Wipe the outer surface of the unit with a soft
dry cloth.
• Do not use solvents or abrasives for cleaning
the unit body.
• Do not immerse the heater body into water or
other liquids; to avoid electric shock, provide
that water does not get into the unit body.
•
To clean the air inlets of the heater you may
use a vacuum cleaner with a corresponding
attachment.
•
After cleaning place the heater into package
and put it for storage in a dry cool place away
from children.
• Avoid contact of the power cord with sharp
objects.
•
Before switching the heater next time, check
its operability and integrity of the power cord
isolation.
5
ENGLISH
13.07.2015 10:34:31