Vitek VT-2167 W Betriebsanweisung Seite 4

ENGLISH
•
Do not wind the power cord around the unit
body.
•
Check the cord insulation integrity periodi-
cally.
•
Do not use the unit if the power plug or the
power cord is damaged, if the unit malfunc-
tions or in case of some damage. In this
case contact the authorized service center for
checking and repairing the unit. Do not repair
the unit by yourself.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
ATTENTION! Portable electric heaters are
intended for additional rooms heating only. They
are not meant for operation as main heating
units.
•
Unpack the unit.
•
Make sure that the switch (1) is in the «OFF»
position.
•
After unit transportation or storage at low
temperature keep it for at least two hours
at room temperature before switching on.
SETTING
Option 1 – Stand mode
•
Unscrew the nut from the axis of wheel (6),
insert the threaded segment of the axis into
the opening of the plate (5) and fix the axis
with the nut. Fix the remaining wheels (6) on
the plates (5) in the same way.
•
Turn the unit over.
• Unscrew the fastening screws intended to
fasten the plates (5), set the plates (5) and fix
them with the unscrewed screws.
• Turn the unit over and set it on the wheels (6).
Option 2 – Wall mounting
Attention! Before drilling a hole in the wall,
make sure that there is no electrical wiring at
this place.
•
When mounting the unit on the wall, ensure
that the mains socket is below the unit and
easy to access. Leave at least 15 cm from
the unit to the floor, 50 cm from the front and
upper panels to any objects and 10 cm from
side panels to any objects.
•
Plates (5) and wheels (6) are not used for wall
mounting of the heater.
VT-2167.indd 4
•
Mark the holes on the wall for the wall brack-
ets (9) in a way that they are not less than
45 cm high from the floor.
•
Drill the holes in the wall to the required depth.
•
Insert the dowels into the holes and fix the wall
brackets (9) with 4х30 mm screws.
• Fix the limit stops (7) on the rear side of the
body with 4х12 mm screws.
•
Hang the heater on the wall having inserted
the wall brackets (9) into the notches (4).
•
Fix the heater having set the wall bracket locks
(8) into the upper parts of the notches (4) and
fix them with 4х12 mm screws.
Using the heater
Insert the power plug into the mains socket.
• Set the switch (1) to the position «ON».
• Press the button (13), the unit will be switched to
the standby mode (previous settings), the room
temperature values will be flashing on the display
(3) during 10 seconds, and then the display will
go out. Press the button (13) again, and the unit
will be operationg in the auto mode at low power.
•
Press the button (13) repeatedly to select the
power level:
– a t high power level the display (3) will show
the indicator .
– a t low power level the display (3) will show
the indicator .
•
If you press the button (13) again, the unit will
be switched back to the standby mode and
the indicator will light up on the display.
Note: Upon switching the unit off, the last
entered parameters (mode, temperature, timer)
remain in memory, return to them takes place
when it is switched on next time.
Temperature setting
•
In the high and low power modes, you can set
the required temperature in the room by press-
ing the buttons (12) «+»/«–». Press the buttons
repeatedly to select the required temperature.
The temperature can be set in the range from
+5 to +35°C. If no buttons are pressed within 3
seconds after the last temperature setting, the
heater starts operating, the display (3) shows
the current temperature in the room.
•
The unit starts heating the room when the
room temperature is 1°С below the preset
temperature, and stops heating when the
room temperature is 1°С above the preset.
4
13.07.2015 10:34:31