Makita DUA300 Betriebsanleitung Seite 16

Attaching the shoulder harness
CAUTION:
When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
If you put on the shoulder harness included in the tool pack-
age and the shoulder harness of the backpack-type power
supply at the same time, removing the tool or backpack-type
power supply is difficult in case of an emergency, and it may
cause an accident or injury. For the recommended hanging
band, ask Makita Authorized Service Centers.
CAUTION:
Always use the shoulder harness
attached to the tool. Before operation, adjust the shoul-
der harness according to the user size to prevent fatigue.
CAUTION:
Before operation, make sure that the shoul-
der harness is properly attached to the hanger on the tool.
CAUTION:
Before operation, make sure that the
buckle of the shoulder harness is fastened firmly.
CAUTION:
Always use the shoulder harness dedi-
cated to this tool. Do not use other shoulder harnesses.
1.
Put on the shoulder harness and fasten the buckle.
► Fig.17: 1. Buckle
NOTE: When removing the shoulder harness, unlock
the buckle and remove the shoulder harness.
2.
Adjust the shoulder harness to a comfortable working position.
► Fig.18
3. Clasp the hook on the shoulder harness to tool's hanger.
► Fig.19: 1. Hook 2. Hanger
The shoulder harness features a means of quick
release. Simply squeeze the sides of the buckle to
release the shoulder harness.
► Fig.20: 1. Buckle
Working with the tool
CAUTION:
Keep all parts of the body away
from the saw chain when the motor is operating.
CAUTION:
Hold the tool firmly with both
hands when the motor is running.
CAUTION:
Do not overreach. Keep proper
footing and balance at all times.
CAUTION:
When cutting through branches,
be careful not to lose your balance due to the
weight of the tool head.
CAUTION:
Always keep escape route in case
a cut branch falls towards the operator.
CAUTION:
Never use the tip of the guide bar
for cutting. Otherwise, dangerous kickback may
occur, and it may result in personal injury.
NOTICE:
Never toss or drop the tool.
NOTICE:
Do not cover the vents of the tool.
NOTICE:
Do not force the tool. Otherwise, it may
damage the tool.
Stand on a stable surface, and hold the tool away from
the branches so that the angle of the tool becomes 60°
or less against the horizontal ground.
► Fig.21: 1. 60° or less
Start the tool, and then press the saw chain onto the
branch lightly.
When cutting long branches, in order to control the drop
position of cut branches, divide the branch in sections
and cut the branch from the tip. Pay attention to the
falling branches since they may bounce in the direction
of the operator after hitting the ground.
► Fig.22
When cutting thick branches, first make a shallow
undercut and then make the finish cut from the top.
► Fig.23
If you try to cut off thick branches from the bottom, the
branch may close in and pinch the saw chain in the cut.
If you try to cut off thick branches from the top without a
shallow undercut, the branch may splinter.
► Fig.24
Carrying tool
Before carrying the tool, always remove the battery
cartridges from the tool, and then attach the guide bar
cover. Also cover the battery cartridge with the battery
cover.
► Fig.25: 1. Guide bar cover 2. Battery cover
Using the tool with battery adapter
Optional accessory
Use the hanging band when you use the tool with bat-
tery adapter.
Attaching the hanging band
1.
Attach the hooks of the hanging band to the rings
of the shoulder harness or waist belt as shown in the
figure. Select the type of band and the connecting
method appropriate for your usage.
► Fig.26: 1. Ring 2. Hook
► Fig.27: 1. Ring 2. Hook
2.
Attach the hook to the tool.
► Fig.28: 1. Hook
Detaching the tool
When setting down the tool, unlock the buckle on the
hanging band with one hand while holding the tool with
the other hand.
► Fig.29: 1. Buckle
NOTE: The buckle is not equipped depending on the
type of band.
If you need to release the tool quickly, follow the steps below.
1.
Push the levers on the buckle of the waist belt to
unlock the buckle.
► Fig.30: 1. Buckle 2. Lever
2. Take off the shoulder harness to release the tool
and the unit.
► Fig.31: 1. Shoulder harness
16 ENGLISH