Automatic Levelling - Bosch GCL Professional 2-50 C Originalbetriebsanleitung

Working with the pendulum lock
Sequence of actions
On/off switch (2) in position " On"
Press the laser operating mode
Laser
button (8) once
Press the laser operating mode
Laser
button (8) twice
Press the laser operating mode
Laser
button (8) three times
If, during work with pendulum lock, you switch to "working
with automatic levelling" mode (on/off switch (2) in position
On), the first combination option of this mode's indicat-
ors is always activated.
Receiver Mode
Receiver mode must be activated when working with the
laser receiver (29), regardless of which operating mode is
selected.
In receiver mode, the laser lines flash at a very high fre-
quency, enabling them to be detected by the laser receiver
(29).
To switch on receiver mode, press the receiver mode button
(6). The receiver mode indicator (7) will light up green.
When receiver mode is switched on, the laser lines are less
visible to the human eye. Therefore, switch receiver mode
off by pressing the receiver mode button (6) again to work
without a laser receiver. The receiver mode indicator (7) will
go out.

Automatic Levelling

Working with Automatic Levelling (see figures B–E)
Position the measuring tool on a level, firm surface or attach
it to the rotating mount (23).
For work with automatic levelling, slide the on/off switch (2)
to the " On" position.
The automatic levelling function automatically levels irregu-
larities within the self-levelling range of ±4°. The measuring
tool has been levelled as soon as the laser beams stop flash-
ing.
If automatic levelling is not possible, e.g. because the sur-
face on which the measuring tool stands deviates by more
than 4° from the horizontal plane, the laser beams will flash
quickly.
If this is the case, set up the measuring tool in a level position
and wait for the self-levelling to take place. As soon as the
measuring tool is within the self-levelling range of ±4°, the
laser beams will light up continuously.
In case of ground vibrations or position changes during oper-
ation, the measuring tool is automatically levelled again.
Upon levelling, check the position of the laser beams with re-
Bosch Power Tools
Horizontal line Vertical line
mode mode
● ●
Cross-line mode
● –
– ●
● ●
Cross-line mode
gard to the reference points to avoid errors arising from a
change in the measuring tool's position.
Working with a pendulum lock (see figure F)
For work with the pendulum lock, slide the on/off switch (2)
to the " On" position. The pendulum lock indicator (5)
lights up red and the laser lines continuously flash slowly.
For work with the pendulum lock, automatic levelling is
switched off. You can hold the measuring tool freely in your
hand or place it on a sloping surface. This means that the
laser beams are no longer levelled and no longer necessarily
run perpendicular to one another.
Remote control via Bluetooth®
The measuring tool is equipped with a Bluetooth® module
which uses radio technology to enable remote control via a
smartphone with a Bluetooth® interface.
Information about the system requirements for a Bluetooth®
connection can be found on the Bosch website at
www.bosch‑pt.com
When remote controlling via Bluetooth®, poor reception con-
ditions can cause time delays between the mobile terminal
device and the measuring tool.
Bosch applications (apps) are available for remote con-
trolling. They can be downloaded in the respective stores,
depending on the terminal/device:
Switching on Bluetooth®
To switch on Bluetooth®, press the Bluetooth® button (10).
Ensure that the Bluetooth® interface is activated on your mo-
bile terminal device.
The connection between mobile end device and measuring
tool is established after the Bosch application has started. If
English | 25
Point mode Pendulum lock
indicator (5)
–
Red
–
Red
–
Red
–
Red
1 609 92A 4HG | (12.11.2020)
Figure
F
F