Washing Brush (18); Operation; Water Supply; Water Supply Via The Domestic Water Network - AL-KO EASY FLEX Betriebsanleitung

Operation

4. Screw (09/b) the bottle with fitted bottle
adapter (09/1) into the connection of high
pressure cleaner (09/2).
4.3.7

Washing brush (18)

1. Align the lug of washing brush (18/1) with the
opening of high-pressure nozzle (18/2).
2. Insert (18/a) washing brush (18/1) into high-
pressure nozzle (18/2).
3. Twist (18/b) washing brush (18/1) until it en-
gages.
5 OPERATION
WARNING! Danger if assembly is not
carried out completely! Operation of an incom-
pletely assembled appliance can result in serious
injury.
■
Operate the device only when it is fully as-
sembled!
■
Insert the rechargeable battery into the appli-
ance only when it has been fully assembled!
■
Check that the attachments have been fitted
correctly before switching on.
IMPORTANT! Danger from water. Contact
with water will lead to short circuits and destruc-
tion of the rechargeable battery.
■
Do not expose the rechargeable battery to
water and moisture when using the appli-
ance.
■
Keep the rechargeable battery dry when
changing the attachments.
5.1

Water supply

IMPORTANT! Danger of damage to the ap-
pliance. The appliance can be damaged if it is
connected to a water supply with dirty, rusty,
muddy or corrosive water. This includes plant fer-
tilisers, plant protection products and cleaning
agents.
■
Clean the appliance with clean water to pro-
long its service life.
5.1.1 Water supply via the domestic water
network
The high-pressure cleaner can be connected to
and operated via the domestic water network.
5.1.2

Water supply from PET containers

The high-pressure cleaner can be operated with
PET containers filled with clean water see chap-
ter 4.3.6 "Bottle adapter (07-09)", page 24.
442923_a
5.1.3

Water supply from open vessels

The high-pressure cleaner can be operated with
water from open vessels, such as rain barrels,
buckets, ponds, etc.
NOTE The priming time is increased of
the maximum suction head is exceeded.
■
Observe the maximum suction head for the
appliance.
1. Connect the hose to the high-pressure
cleaner (05).
2. Hang hose filter (01/10) in an open vessel.
■
Attach hose clip (01/13) to the edge of
the vessel.
■
Float (01/11) prevents hose filter (01/10)
from sinking to the bottom of the vessel.
Before use
Before use, allow the air to escape from the hose.
1. Hold the high-pressure cleaner at waist level
(< 1.5 m).
2. Start the appliance (10) see chapter 5.2

"Starting and stopping the appliance (10)",

page 25.
3. Wait until the high-pressure cleaner starts to
spray water before starting work. This takes
at least 30 seconds, depending on the type of
water supply.
5.2 Starting and stopping the appliance (10)
Starting the machine
1. Direct the appliance towards the surface to
be cleaned.
2. Press and hold (10/a) locking switch (10/1).
3. Press and hold (10/b) lever (10/2) on the ap-
pliance.
Stopping the appliance
1. Release lever (10/2).
2. Release locking switch (10/1).
5.3

Watering and cleaning

5.3.1 Settings of the multi-spray nozzle (11,
12, 13, 14)
CAUTION! Risk of injury. Do not adjust the
nozzle setting during operation.
■
Stop the appliance and then change the noz-
zle setting.
The multi spray nozzle has five different spray
patterns. Select a suitable nozzle function for
your application.
25