Samsung PS50B679 Benutzerhandbuch Seite 15

❑ Satellite System Setup
Set the LNB used for receiving broadcasting signal.
N
Satellite System Setup
N
The PIN input window appears.
N
Before running Auto Store, set Satellite System Setup. Then channel scan is run
normally.
„
LNB Power
Enables or disables the power supply for the LNB.
Set whether TV provides power supply of LNB.
This function is for making only one TV can provide power supply when using one LNB
connecting to two TVs.
„
LNB Settings
Conigures the outdoor equipment
• : Selects the satellite for receiving digital broadcasts.
Satellite
• : Selects a transponder from the list or adds a new transponder.
Transponder
• : Selects DiSEqC mode for the selected LNB.
DiSEqC Mode
•
Lower LNB Oscillators
•
Upper LNB Oscillators
• : Selects the 22kHz tone depending on the LNB type. For a universal LNB it should be Auto.
Tone 22 KHz
• : Display the current status of broadcasting signal.
Signal Quality
„
Positioner Settings
• : Enables or disables the positioner control
Positioner
• : Sets the positioner type between DiSEqC 1.2 and USALS
Positioner Type
(Universal Satellite Automatic Location Sysem).
• : Sets the position of satellite antenna according to each satellite. If you
User Mode
store the current position of satellite antenna according to a certain satellite, when the
signal of that satellite is needed, the satellite antenna can be moved to pre-populated
position.
: Selects the satellite to set the position for.
- Satellite
: Selects a transponder from the list for signal reception.
- Transponder
: Selects the movement mode between discrete and continuous
- Moving Mode
movement.
: Adjusts the step size degrees for the antenna rotation. Step Size is
- Step Size
available when Moving Mode is set to Step.
- Go To Stored Position
- Antenna Position
- Store Current Position
: Display the current status of broadcasting signal.
- Signal Quality
• Installer Mode : Sets the antenna movement limits.
: Selects the direction of the Positioner Limit.
- Limit Position
- Antenna Position
- Store Current Position
: Moves the antenna to the reference position.
- Go To Zero
- Reset Positioner Limit
„
Reset All settings
All satellite settings will be reset to the initial values.
is available when Antenna is set to Satellite.
: Sets the LNB oscillators to a lower frequency.
: Sets the LNB oscillators to a higher frequency.
: Rotates the antenna to the stored satellite position.
: Adjusts and stores the antenna position for the selected satellite.
: Stores current position as the selected positioner limit.
: Adjusts the antenna position for the Positioner Limit by pressing the left or right key.
: Stores the current position as the selected Positioner Limit.
: Allows the antenna to rotate over the full arc.
English - 15
Satellite System Setup
LNB Power : On
LNB Settings
Positioner Settings
Reset All Settings
U E
Move Enter
LNB Settings
Satellite : Astra_19.2E
Transponder : 10743 MHz, H/L
DiSEqC Mode : 2/4
Lower LNB Oscillators : 9750 MHz
Upper LNB Oscillators : 10600 MHz
Tone 22 KHz : Auto
Signal Quality
U E
Move Enter
Positioner Settings
Positioner : On
Positioner Type : USALS
User Mode
Installer Mode
U E
Move Enter
User Mode
Satellite : Astra_19.2E
Transponder : 10743 MHz, H/L
Moving Mode : Step
Step Size : 1
Go To Stored Position
Antenna Position : West l
Store Current Position
Signal Quality
U E
Move Enter
►
R
Return
►
0
R
Return
►
R
Return
►
rEast
0
R
Return