AVIRE Memcom+ Einbauanleitung Seite 16

Old Programming Mode
The old programming menu is still available on the Memcom
old programming passcode (default- *1234#). The old method of programming can also be used remotely, by dialing the phone number of the
Memcom, and following the same instructions.
Old Menu Structure
*94 Total Count
*93 Due in Count
*92 Service Count
*91 Model/HW/SW
*90 GSM Signal
*84 EOA
*83 Not in Use
*82 Relay o/ride
*81 GSM SIM Pin
*61 Language
*52 Service Count
*51 Serv. Interval
*43 Guidance
*42 Reassurance
*41 Location
*40 Relay Mode
*39 PBX Freq.
*38 Hangup delay
*37 Test Call on
*36 Tech 2 Delay
*35 Tech 1 Delay
*34 TopOfCar Dly
*33 MPS Delay
*32 Answer Delay
*31 In-Car Delay
*29 GMT Offset
*28 Network ID
*27 Hardware Mon.
*26 Hardware Opts
*25 Set Date
*24 Set Time
*23 Speaker Vol.
*22 Password
*21 ID Code
*17 Dial Attempts
*16 Background
*15 Tech Alm
*14 Alarm No4
*13 Alarm No3
*12 Alarm No2
*11 Alarm No1
If you require any further assistance when programming the Memcom
01628 540160.
Memco is a brand of Avire
unit. To access this mode of programming, from the idle screen, simply enter the
+
Quick Start Guide to programming...
Programming options for the type of Memcom
*11 1st (Alarm Tel Number) # Program 1st Alarm Number
*15 5th (telephone alarm number) **1# Program Technical Alarm Number
*16 6th (telephone alarm number) **1# Program EN81-28 Background Test Call Number
Suffix Protocol
# Guided message for call centre
**0# No guided message for call centre.
**1# Memco Protocol - compatible with Avire Hub, Memcom ETR Software or
GlobalNet
**3# P100 Protocol - Recommended for Avire Hub.
**4# Alternative to # for use when Memcom is configured for Hotline operation.
**6# Contact ID Protocol
*23 Volume TOC 5, COP 0 Adjustable between 0-9 (0 = minimum setting)
*41 Location message: 1: Play Location 2: Record Location Message
*26 Hardware
Defaults: 12 TOC Version 8 COP Version
1 = EN81-28 operating mode opts
2 = Service Input = Tech.2
4 = Disable internal microphone
8 = Consecutive dial mode
16 = Enable Memcom + GSM module
64 = Alarm Input N/C
128 = Czech, Greek, Italian and Singaporean
dial tone cadences for use with multiple
Memcom only
+
256 = Service Input as Alarm Activation
512 = COP Accessory attached (450 200 & 450
250).
Any combination can be programmed. Enter
sum of the numbers of the options required.
Exiting Programming
Press # to return to programming home screen, then enter one of the following exit
codes...
*01# Exit programming without making an alarm call
*03# Exit programming and call Alarm number 6 EN81-28
*021# Exit programming and call Alarm number 1 only
*035# Exit programming and call Alarm Number 5 Technical Alarm
Avire Trading Ltd
Unit 1, The Switchback
Gardner Road
Maidenhead
Berkshire SL6 7RJ, UK
+ Alarm / Software Calls
*27 Hardware Monitoring
Default: 39
1 = PSU monitoring
2 = Battery supply
4 = Phone line, (Do not use if
connected to a hotline)
8 = GSM Low signal
16 = GSM No signal
32 = Microphone/speaker test
64 = Power Logging
Any combination can be
programmed. Enter sum of the
numbers of the options required.
unit, please call our Technical Service Team on
+
T: 01628 540100
E: sales.uk@avire-global.com
W: www.avire-global.com
16 16