Introduction; Layout; Scope Of Delivery; Intended Use - HERKULES 3906220931 Originalanleitung

GB

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment
and success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
WE RECOMMEND:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat-
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re-
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack-
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating the
machine and carefully follow its information. The ma-
chine can only be operated by persons who were in-
structed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with.
18 І 104
2. Layout (Fig. 1-M)
Tank indicator
1.
Tank cover
2.
2 x 230 V~ socket-outlets
3.
4. Earth connection
Overload cut-out
5.
Voltmeter
6.
Oil filler screw
7.
Oil drainage screw
8.
Oil deficiency protection for low oil switch-off
9.
On/Off switch
10.
11. Choke lever
Reversing starter
12.
Petrol cock
13.
Wheels
14.
Axle
15.
Foot
16.
17. Push bar holder
18. Push bar
Screws size M8 x 40
19.
Screws size M8 x 16
20.
Washers for wheels
21.
Securing split pins for wheels
22.
Nuts M8
23.
24. Spark plug wrench
Screwdrive
25.
Open end wrench 10/12 mm
26.

3. Scope of delivery

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

4. Intended use

The device is designed for applications operated with a
230 V alternating current source.
Be sure to observe the restrictions in the safety instruc-
tions. The generator is intended to provide electric power
tools and light sources with electricity.
When using the device with household appliances,
please check their suitability in accordance with the rel-
evant manufacturer's instructions. In case of doubt, ask
an authorized dealer of the respective equipment.
The equipment is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of misuse.
The user/operator and not the manufacturer will be li-