sammic MO-1834 Gebrauchsanweisung Seite 21

This allows the user to cook food items at manual cook mode
and programming mode.
1) Three stages can be set at most under cooking mode or pro-
gramming mode.
After setting the power and time for the first stage, press "Time
Entry" to set the second stage. And the same step to set the
third stage.
2) When setting the second, third stage, press "Time Entry",
"STAGE-2", "STAGE-3" displays.
3) Press " " button to start cooking.
Example: In programming mode, press number buttons "3" to set
two stages cooking. The first stage is PL7 and time is 1 minute 25
seconds. The second stage is PL5 and 5 minutes and 40 seconds.
The steps are as follows.
a. Open the door, press number button "1" for 5 seconds,
"PROGRAM" displays.
b. Press number button "3", the screen will display "P:03". After
two seconds, the screen will display the related time ":30".
c. Press "1", "2", "5" to input the cooking time. "1:25" displays.
d. Press "Med-Hi 70%", "1:25 70" displays.
The first stage is finished.
e. Press "Time Entry", "STAGE-2" displays.
f. Press "5", "4", "0" button, "5:40" displays.
g. Press "Medium 50%", "5:40 50" displays.
The second stage is finished.
h. Press " " button to start cooking.
i. The total time counts down.
Use Option Mode
14.
This allows the user choose between various ways for the oven
to operate.
1) Open the oven door and press "2" pad for 5 seconds.
The buzzer sounds once and enter this mode.
2) The screen displays "OP: - -".
3) Press any number button to enter related mode setting.
For example: to set the voice of the buzzer to medium. Press
"2", "OP:22" displays.
If you want to change, keep pressing "2", the screen displays
"OP:20", "OP:21", "OP:22", "OP:23", "OP:20" in cycle.
4) Press " " to save the current setting. After saved, "OP: - -"
display again.
5) During setting process, press "
Close the door will enter Ready Mode.
6) If " " button not pressed at the last step, the program can-
not be saved but stay at previous way.
Service Mode
15.
1) Open the oven door and press "3" pad for 5 seconds to enter
service mode.
2) The screen displays "SERVICE".
3) To check the times of closing or opening the door, just press
number button "3", the screen will display the times.
4) If press "1" pad for Tube Hours.
If press "2" pad for Tube Cycles.
If press "3" pad for Door Cycles.
If press "4" pad to Clear service information.
" to enter Door Open Mode.
21
- 21 -
Only for some models:
If press "5" pad to run Top Mag. Oven displays amps.
If press "6" pad to run Bottom Mag. Oven displays amps.
5) Press " " to enter Door Open Mode. Close the door will
enter Ready Mode.
Factory-default setting
16.
In the Ready Mode, pressing "
setting.
1) Press " " and "0", the buzzer sounds once, and the screen
will display "CHECK". If it is in the factory-default setting, the
screen will display "11", after three seconds, the oven turn to
the ready mode.
If not in the factory-default setting, the screen will display "00",
press " " to the factory-default setting, the screen will dis-
play "CLEAR". the buzzer sounds once, after self-testing, the
screen will display "11" or "00".
2) If do not press " " when the screen display "00", the setting
will cancel.
Note: Be careful in the operation as it will restore all configure to
factory-default setting.
How to remove and install the filter
Turn the metal nails left to loosen them.
Take off the filter.
To reinstall, align the base plate mounting holes, clockwise the
metal nails to tighten.
" and "0" to factory-default
EN ES