Operation; Maintenance; Optional Accessories - Makita DPT350 Betriebsanleitung

CAUTION:
• Do not use deformed connected pin nails. Use pin nails
specified in this manual. Using pin nails other than
those specified may cause pin nail jamming and
breakage of the pin nailer.
Unloading pin nailer
CAUTION:
• When removing pin nails, make sure that your fingers
are not placed on the trigger or the lever and the
battery cartridge is removed from the pin nailer.
Misfiring may cause personal injuries and property
damage.
Remove the battery cartridge.
Press the locking lever and slide the magazine.
Take out pin nails from the magazine slit.
Nose adapter
CAUTION:
• Always make sure that your fingers are not placed on
the trigger or the lever and the battery cartridge is
removed before installing the nose adapter. (Fig. 10)
When firing pin nails on the material to be fastened with
easily-marred surfaces, use the nose adapter. To install
the nose adapter, place it over the driver guide cover so
that the protrusion inside the nose adapter fits to the slit in
the driver guide cover.
When not in use, store the nose adapter in the holder at
the back end of the magazine to keep it from being lost.
Hook
CAUTION:
• Always make sure that your fingers are not placed on
the trigger or the lever and the battery cartridge is
removed before using the hook. (Fig. 11)
CAUTION:
• Do not hang the hook from the waist belt. Dropping the
pin nailer, which is caused by the hook accidentally
coming out of place, may cause misfiring and personal
injuries. (Fig. 12)
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
Hex wrench storage (Fig. 13)
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.

OPERATION

Driving pin nails
WARNING:
• Before pulling the trigger, always make sure that the
opening that pin-nails are fired contacts material to be
fastened. Just pulling the trigger fires pin nails.
Misfiring may cause personal injuries. (Fig. 14)
Place flat the opening of the tool that pin-nails are fired on
the material to be fastened and hold the tool firmly against
the material. Then pull the lever and then pull the trigger
fully to drive the pin nail. The grip is shaped so that the
tool head can be held down securely with index finger and
thumb. After driving a pin-nail, be sure to release the
trigger fully. (Fig. 15)
When the head of driven pin-nail remains above the
surface of the material, drive the pin-nail while holding the
pin nailer head firmly.
NOTE:
• When the trigger is pulled after a quick trigger action,
the nailer may do nothing but operates momentarily
and may not fire pin nails. This is not a trouble. At this
time, release the trigger once, pull it again and the pin
nails can be fired.
• Using the pin nailer continuously with the head of fired
pin nails remaining above the surface of material to be
fastened may cause damage to the driver of the pin
nailer and nailer jamming etc.
Removing jammed pin nails
WARNING:
• Always make sure that the lever is released and the
battery cartridge is removed before removing jammed
nails. (Fig. 16)
Remove the battery cartridge from the pin nailer.
Take out pin nails that remain inside the magazine.
Loosen bolt (A) and bolt (B) by turning them
approximately two turns using the hex wrench provided
with the pin nailer.
Remove driver guide cover by sliding it.
Remove stuck pin nails, debris, adhesives and woodchips
etc. from the passage for pin nails.
Check the driver guide cover for stuck pin nails or other
foreign matters and then secure it with these two bolts.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
• To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized Service Centers,
always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Pin nails
• Various type of Makita genuine batteries and chargers
• Safety goggles
7