Siemens Intrunet E-Serie Bedienungsanleitung Seite 3

Instruction
en
ADM-I12W1 motion detector
The detector detects movement in the
room under surveillance
an alarm. It responds most sensitively to
movement in the directions indicated by
arrows B / D. The alarm is transferred
7
by wireless. The back tamper recognizes
if the detector is removed with force.
Prerequisites
The detector should be installed by peo-
ple with specialist knowledge and in
compliance with valid regulations.
The detector is only intended
for indoor use. Note the posi-
tioning instructions
Opening the detector
1. Check the scope of delivery
2. Slide up the screw-on cover
loosen the screw
3. Pull the housing front
2 C.
Fitting the detector
1. Fit the mounting base
- Define type of fastening
refer to mounting bracket option)
- Break open three fixing holes.
- Fit mounting base at the proposed
height.
The mounting base should be
secured using two screws
4 A / B and the back tamper
with one screw
2. Pull out insulation strip between bat-
tery and bracket
3. Press the tamper contact
ter the detector with the system.
For safety reasons only use
the battery supplied and not
any other type.
4. Fold front
2
base 2 C and secure with screw
Slide down screw-on cover
Programming
To adjust the settings to the application,
move the switches into the corresponding
positions:
PIR sensitivity
Low sensitivity, for busy envi-
ronments.
Downloaded from www.Manualslib.com
7 and initiates
* factory setting
Pet immunity
12kg
* factory setting
Sensitivity setting
-
.
6
1 .
* factory center is the middle position
2 A and
(12-meter field of vision)
2 B.
2 D off the base
ID registration
You will find instructions for integrating
the detector in the control panel in the
control panel's installation manual.
2 C as follows:
4 A / B. (also
Walk test
1. Call up walk test mode in the control
2. Hold a magnet to the right of the de-
3. Run the walk test for alarm triggering
4 C.
Alarm transmission test
1. Call up walk test mode in the control
8 A.
2. Hold a magnet to the right of the de-
5 B to regis-
3. The alarm transmission test has now
D back onto mounting
4. The test is passed if the control panel
2 B.
2 A.
Options
Narrow angle lens kit AO-C25
The kit enables the detection area cov-
erage to be defined to a narrow angle as
shown in
Loosen the lens currently at the positions
5 B
shown in
tector. Insert adapter
and press down narrow angle lens.
manuals search engine
High sensitivity, for quiet
environments.*
5 A
PET
Suppresses alarm for pets
up to a weight of 12 kg.*
Suppresses alarm for pets
up to a weight of 30 kg.
5 D
+
* Turn potentiometer 5
the position required to
adjust detector to room size
and field of vision.
panel.
tector for 1 second B.
8
in the whole detection area 7 of the
detector.
panel.
tector for at least 2 seconds 8 B.
started. 11 test signals are sent to the
control panel at an interval of 6 sec-
onds (the LED 10 flashes during each
transmission).
receives the test signals and indicates
this accordingly.
7 D.
F and remove from the de-
5
3 C in to detector
- 3 -
White light filter AO-WL10k
The white light filter is needed for applica-
tions with extreme white light interference
(> 4000 lux).
Loosen the lens currently at position
and remove this from the detector. Insert
adapter 3 B in to detector and press the
lens back down.
Wall & ceiling mounting brackets
The mounting brackets AZ-MBG2
(ceiling 9 B and wall
be used to swivel the detector ± 45°.
Technical data
D into
Detection area
coverage
wide angle 7 B
Detection area
coverage
narrow angle 7 D
Range of wireless
module
Frequency:
ADM-I12W1
ADM-I12W2
Identification
Data protocol
Event transmission
Test mode
Battery power sav-
ing
Battery
Warm up period
Pet immunity
EMI rejection up to
2 GHz
Operating tempera-
ture
Storage tempera-
ture
Air humidity
EN 60721
Type of housing
protection
EN 60529,
EN 50102
en
5 F
9
9
A
9 C mounting) can
12 m
20 m
Up to 300 m out-
doors
868 MHz
916 MHz
ID serial number
24 bits
SiWay
Alarm, sabotage,
surveillance, bat-
tery low
Walk test & alarm
transmission test
Automatic energy
saving function
Lithium 3 V
Type: xx123
Size: 2/3 AA
Capacity:
1550mAh
60 ± 5 s
< 12 kg
< 30 kg
> 10 V/m
-10 °C ... +50°C
-20 °C ... +60 °C
< 85 %rF, not
condensing
IP41 / IK02