Renkforce CM518 Bedienungsanleitung Seite 2

G Operating instructions
CM518 Headset Microphone
Item no. 1267830
Intended Use
The headset microphone is intended for converting acoustic signals (sound waves) into electric
signals.
The low-level audio output may be connected only to suitable microphone inputs of audio devices.
Any use other than as described above may lead to damage to the product and can also be dan-
gerous.
This product complies with the applicable national and European regulations.
All names of companies and products are the trademarks of the respective owners. All rights
reserved.
The safety instructions have to be followed without fail.
Safety Instructions
T he warranty will be void in the event of damage caused by failure to observe these
safety instructions. We do not assume any liability for any resulting damage.
W e shall not accept liability for damage to property or personal injury caused by in-
correct handling or non-compliance with the safety instructions. In such cases, the
warranty will be null and void.
A n exclamation mark indicates important notes in these operating instructions, which
should always be observed.
• For safety reasons, any unauthorised conversion and/or modification of the headset micropho-
ne not permitted.
• Operate the headset microphone via a device with phantom powering (1-10 V/DC) only.
• When connecting the headset microphone, pay attention to the safety instructions of the device
to which it is to be connected.
• Do not expose the product to high temperatures, strong vibrations, dripping water or water
spray.
• Use the product only in a temperate climate, never in a tropical climate.
• Don't leave packaging materials lying around carelessly; they maybe become a dangerous
plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer's Liability Insu-
rance Association for Electrical Systems and Operating Facilities are to be observed.
• If in doubt about how to connect the product correctly, or should any questions arise that are
not answered in these operating instructions, please contact our technical advisory service or
another specialist.
Features
The CM518 headset microphone is a high-quality condenser microphone for voice recording.
The range of use includes uses in the DJ industry, in studio recordings, conferences and transmis-
sions, but also in the multimedia industry and in the communications technology.
The headset microphone is equipped with the following features:
• Easily and flexibly adjustable
• Pleasant and comfortable to wear
• Low inherent noise
• Wide frequency spectrum
Getting Started
B efore using the product, please read the complete operating instructions thoroughly
in order to ensure its proper functioning.
T o avoid distortion or mismatches that could damage the headset microphone or the
connected audio device, connect the headset microphone only to suitable micropho-
ne inputs. To do this, please pay attention to the connection data in the „Technical
data" section.
N ever point the headset microphone at the sound openings of loudspeakers, since this
may lead to interference, which could damage the loudspeaker and the connected
amplifier.
• Put the headset microphone on and direct the neck of the microphone as desired.
• Lay the connection cable to your transmitter unit (body pack).
• Switch off the transmitter unit to which the headset microphone is to be connected.
• Turn the volume for the microphone input on the transmitter unit all the way down.
• Connect the headset microphone to the microphone jack of the transmitter unit.
• To avoid wind noise, you can place the enclosed windscreen on the microphone head.
• Switch the transmitter unit on and adjust the transmitter unit's sensitivity to match the headset
microphone using the corresponding input level control (for this purpose, see the transmitter
unit's user manual).
Disposal
Electronic devices are recyclable waste materials and must not be disposed of in the
household waste!
Dispose of an unserviceable product in accordance with the relevant statutory regula-
tions.
Technical Data
Impedance ....................................................600 Ohm ± 30% (@1 kHz)
Frequency range ..........................................100-10000 Hz
Sensitivity ......................................................-66 dB ±3 dB (0 dB = 1 µbar@1 kHz)
Polar patterns ...............................................Cardioid
Max. level ......................................................110 dB
Phantom powering.......................................1-10 V/DC
Weight ............................................................42 g
Frequency response
Polar patterns
Dimensions
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.